Garmin GPSMAP 8X10, Руководство пользователя

Страница: 76 / 110

Digital Switching
Your chartplotter can be used to monitor and control
circuits when connected to a compatible digital switching
system.
For example, you can control the interior lights and
navigation lights on the vessel. You can also monitor live
well circuits.
To access the digital switching controls, select
Vessel >
Switching .
For more information about purchasing and configuring a
digital switching system, contact your Garmin dealer.
Adding and Editing a Digital Switching Page
You can add and customize digital switching pages on the
chartplotter.
1 Select Vessel > Switching > Options > Setup .
2 Select Add Page or Edit Page .
3 Set up the page as needed:
• To enter a name for the page, select
Name .
• To set up the switches, select Edit Switches .
• To add an image of the boat, select Add BoatView
Image .
NOTE: You can use the default vessel image or use
a custom image of your vessel. You should save the
custom image to the /Garmin folder on the memory
card. You can also adjust the view and placement of
the image.
Garmin Boat Switch
™
WARNING
Garmin strongly recommends using a professional
installer with proper knowledge of electrical systems to
install the device. Incorrectly installing the device can
result in serious bodily injury and damage to the vessel
or the battery.
Configuring the Garmin Boat Switch Device
Some digital switches controlled by the Garmin Boat
Switch device must be configured before use.
Configuring a Switch as Momentary
All latching and momentary channels on the Garmin
Boat Switch device must be configured in the chartplotter
software as momentary switches for proper operation.
1 From a Garmin chartplotter connected to the same
NMEA 2000 network as the Garmin Boat Switch
device, select
Options > Settings > My Vessel >
Switching > NMEA Standard .
2 Select the switch number.
3 Select Configuration > Momentary .
Naming a Switch
You can provide a custom name to be used instead of the
default name for each switch.
1 From a Garmin chartplotter connected to the same
NMEA 2000 network as the Garmin Boat Switch
device, select
Options > Settings > My Vessel >
Switching > NMEA Standard .
2 Select the switch number.
3 Select Name > Change Name .
4 Enter a new name.
5 Select Done .
Labeling a Switch
You can provide a custom label for each switch. The
switch label is separate from the switch name.
1 From a Garmin chartplotter connected to the same
NMEA 2000 network as the Garmin Boat Switch
device, select
Options > Settings > My Vessel >
Switching > NMEA Standard .
2 Select the switch number.
3 Select Label > Edit Label .
4 Enter a new label.
5 Select Done .
Showing and Hiding Switches
You can select which switches are hidden or displayed on
the Garmin chartplotter.
1 From a Garmin chartplotter connected to the same
NMEA 2000 network as the Garmin Boat Switch
device, select
Options > Settings > My Vessel >
Switching > NMEA Standard .
2 Select the switch number.
3 Select Visibility to show or hide the switch.
Configuring the Navigation Light Option
WARNING
It is your responsibility to comply with applicable laws,
regulations, and standards related to the use and/or
operation of marine navigation lights. Garmin is not
responsible for any fines, penalties, citations, or damages
that may be incurred due to any such lack of compliance.
By default, channels 1 and 2 are interlocked for
navigation lighting to satisfy the international regulations
for preventing collisions at sea. Depending on the lighting
specifics of your boat, you may need to configure the
Garmin Boat Switch device to use the wiring option you
that applies to your installation type.
If you do not intend to connect navigation and anchor
lights to the device, you can configure channels 1 and 2 to
operate independently as normal latching switches.
1 From a Garmin chartplotter connected to the same
NMEA 2000 network as the Garmin Boat Switch
device, select
Vessel > Switching .
2 Press and hold switch 1 for 5 seconds.
Switch 1 starts flashing.
66 Digital Switching