manualshive.com logo in svg

Fujitsu XG1200, Руководство пользователя

Поделиться
Скачать
Fujitsu XG1200 Скачать руководство пользователя страница 3

XG1200 User's Guide 

3/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

About this Manual 

This section describes target readers, contents, notations, etc. of this guide. 

Target readers and required knowledge 

This guide has been written for administrators, who are in charge of network construction, maintenance, and management. 
To use this guide, the following knowledge is required. 

 

Basic knowledge of networks, the Internet, and intranet 

 

Basic knowledge of system security 

This guide omits explanations of network protocol terms. 

Contents 

This guide to the XG1200 is composed of the following chapters. 

Chapter 1. Features and Functions 

Describes the features and functions. 

Chapter 2. Using the CLI 

Describes operating environment of CLI and how to operate CLI. 

Chapter 3. Installation 

Describes the necessary installation procedures. 

Chapter 4. Functions and Procedures for Setting Functions 

Describes how to use the console screen. 

Chapter 5. Command References 

Describes how to use the commands. 

Chapter 6. Managing the XG1200 

Describes the management of the XG1200. 

Chapter 7. Troubleshooting 

Describes how to solve problems in the XG1200. 

Appendix A. Event Logs 

Describes the contents of messages reported by the XG1200 and actions to be taken for each message. 

Appendix B. SNMP Traps 

Describes message format of SNMP traps. 

Appendix C. List of MIBs 

Describes the list of MIBs supported by the SNMP agent 

 

Related Manuals 

The following are XG1200 related manuals. Use these manuals as necessary. 

 

XG1200 Series Hardware Guide 

Describes the hardware of the XG1200. 

Symbols Used in This Guide 

The symbols used in this guide have the following meanings. 

 

indicates useful information related to using the XG1200. 
 

 

indicates precautions which must be taken when using the XG1200. 
 

 

indicates supplementary information. 
 

 

indicates related matters such as operation procedures, etc. 

Содержание XG1200



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды