Fujitsu XG1200 Скачать руководство пользователя страница 116

Страница: 116 / 258

XG1200 User's Guide

116/258

5.8.13 multicast-forwarding

Function

Sets forwarding method of multicast frames.

Use the no form to return to the default setup.

Prompt

xg(config)# , or xg(config-agg)#

Command syntax

multicast-forwarding { forward-all | forward-unregistered-mac |
filter-unregistered-mac }
no multicast-forwarding

Parameter

{ forward-all | forward-unregistered-mac | filter-unregistered-mac }

Specifies forwarding method of multicast frames.

−

Forward-all

All multicast frames will be forwarded (flooded).

−

Forward-unregistered-mac

Multicast addresses yet to be registered in the static MAC address table, and multicast addresses registered as
member ports will be forwarded (flooded). Multicast addresses registered as non-member ports will be filtered.

−

Filter-unregistered-mac

Only Multicast addresses registered as member ports in the static MAC address table will be forwarded.

Command type

Configuration command

Default

forward-all

Example

Move to the interface edit mode of the switch ports 1 to 3, and set it to unregistered multicast forwarding mode.

xg(config)# interface port range 1 3
xg(config-if)# multicast-forwarding forward-unregistered-mac

Содержание XG1200































































































































































































































































Результаты поиска

Содержание XG1200

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu XG1200, Руководство пользователя

Результаты поиска

Содержание XG1200

Отзывы:

Бренды по названию

Популярные бренды