manualshive.com logo in svg

Fujitsu XG1200, Руководство пользователя

Поделиться
Скачать
Fujitsu XG1200 Скачать руководство пользователя страница 122

XG1200 User's Guide 

122/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

5.9.2 spanning-tree 

Function 

Enables Spanning Tree Protocol (STP). 
Use the no form to disable Spanning Tree Protocol. 

Prompt 

xg(config)# 

Command syntax 

spanning-tree 
no spanning-tree

 

Command type 

Configuration command 

Default 

None 

Example 

Enable Spanning Tree Protocol. 

xg(config)# spanning-tree 

 

5.9.3 spanning-tree protocol 

Function 

Sets whether Spanning Tree Protocol is applied to each port. 
The no form of this command is used to return to the default setup. 

Prompt 

xg(config-if)#, or xg(config-agg)# 

Command syntax 

spanning-tree protocol { rstp | none } 
no spanning-tree protocol

 

Parameter 

 

rstp 

Sets the currelntly editing port in the interface edit mode to RTSP (IEEE 802.1w Rapid Spanning Tree Protocol) mode. 

 

none 

Sets the STP not to be applied to the currently editing port in the interface edit mode. 
If STP is not applied, when BPDUs are received at this port, the port state will note change, and aloways remain in 
forwarding state. Also, BPDU frame will not be sent from this port. 

Command type 

Configuration command 

Default 

rstp 

Example 

Set ports 1 to 8 collectively to RSTP mode. Then, change port 3 so that Spanning Tree Protocol will not be applied. 

xg(config)# interface port range 1 8 
xg(config-if)# spanning-tree protocol rstp 
xg(config-if)# exit 
xg(config)# interface port 3 
xg(config-if)# spanning-tree protocol none 

 

Содержание XG1200



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды