manualshive.com logo in svg

Fujitsu XG1200, Руководство пользователя

Поделиться
Скачать
Fujitsu XG1200 Скачать руководство пользователя страница 160

XG1200 User's Guide 

160/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

 

5.14.2 monitor traffic-counts 

Function 

Displays the transmission frame count at each port. 

Prompt 

xg> or xg# 

Command syntax 

monitor traffic-counts { current | total } [interval <3-60>] 

Parameter 

 

{ current | total } 

Specifies the statistics to be displayed. 

− 

current 

Displays the number of cumulative transmission frames after startup of this command. 

− 

total 

Displays the number of cumulative transmission frames after startup of the system. 

 

interval <3-60> 

Specifies the statistics updating interval (in seconds).   
The default interval is 3 seconds. 

Command type 

Operation management command 

Output format (if "current" is specified) 

xg# monitor traffic-counts current 
Traffic  Statistics(Current  Frame  Counts)                                  2005/08/22-12:12:15 
========================================================================================== 
Port  Link  State/   Tx-Frame   Rx-Frame    Tx-Frame    Rx-Frame      Rx-Bcast      Rx-Mcast    
        STP  State    Counts/S   Counts/S    Counts       Counts        Counts         Counts      
----  ----------   ----------  ----------  -----------  ------------  ------------  ------------ 
   1   Up/Discard   12345678K  12345678K  1234567890K  1234567890K  1234567890K   1234567890K 
   2   Down                    0          

 

0              0              0              0              

 

0 

   3   Up/Discard          

 

923         923  1234567890K  1234567890K  1234567890K  

 

1234567890K 

   4   Up/Learn         

 

999123     

 

999123  1234567890M         

 

256M         

 

256M           256M 

   5   Up/Forward          

 

999         999  1234567890G         

 

256G         

 

256G           256G 

   6   Up/Forward       999999     

 

999999  1234567890T         

 

256T         

 

256T           256T 

 

Port  

Displays port numbers. Statistics of each port are displayed on a line. 

 

Link State/STP State 

Displays the port state in the Link State or STP State format. 
The Link State may indicate one of the following link states. 

− 

Down 

The port link is down.   

− 

Up 

The port link is up. 

The STP State displays the current port status based on the STP (Spanning Tree Protocol). Note that the STP State is 
not displayed if the Link State is Down. 
For port status details, see “Spanning Tree

 Protocol Port Stat

e

s

”

.

  

 

Tx-Frame Counts/S 

Displays the transmission frame rate (in fps) using an 8-digit, right-justified value. 

 

Rx-Frame Counts/S 

Displays the receive frame rate (in fps) using an 8-digit, right-justified value. 

 

Tx-Frame Counts 

Displays the number of cumulative transmission frames after execution of this command, using a 10-digit, right-justified 
value. 

 

Rx-Frame Counts 

Displays the number of cumulative receive frames after execution of this command, using a 10-digit, right-justified 
value. 

 

Rx-Bcast Counts 

Displays the number of cumulative receive broadcast frames after execution of this command, using a 10-digit, 
right-justified value. 

 

Rx-Mcast Counts 

Displays the number of cumulative receive multicast frames after execution of this command, using a 10-digit, 
right-justified value.

 

 

 

Содержание XG1200



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды