manualshive.com logo in svg

Fujitsu XG1200, Руководство пользователя

Поделиться
Скачать
Fujitsu XG1200 Скачать руководство пользователя страница 211

XG1200 User's Guide 

211/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

6.1.2 Verifying System Status 

Verify the status of system by entering the "

show system information

" command in the operator EXEC mode or in the 

administrator EXEC mode. 
The following example shows the information that is displayed when the "

show system information

" command is entered. 

xg# show system information 

System  Information  2005/08/22-21:06:11 
======================================= 
 System Name (hostname) : xg 
 System  Location          :  (none) 
 System  Contact           :  (none) 
 Default  Banner           :  XG1200  E99L99  XF9999 
 Startup  Time             :  2005/08/22-19:28:24 
 Startup-config Modified: 2005/08/22-19:54:01 
 Firmware  Information 
  Firmware[1]             :  E99L99  XF9999  2005/08/21-18:42:52 
   Updated  Time           :  2005/08/21-22:08:12 
  Firmware[2]             :  E99L99  XF9999  2005/08/22-19:27:12 
   Updated  Time          :  2005/08/23-10:57:53 
  Current  Firmware      :  [2] 
  Next Startup Firmware: [2] 
  Boot  Loader            :  E10L10  XF0043 
 Timezone                 :  gmt  +0900 
  (Next  Boot)            :  gmt  -800 
 Summer-Time             :  (none) 
  (Next  Boot)            :  M4.1.0/0200  M10.5.0/0200  0100 
 RS232C  Baud-Rate        :  9600 
 Management LAN Information 
  MAC  Address            :  0080.17c2.0500 
  IP  Address/Mask       :  192.168.41.22/24 
  Default  Gateway       :  192.168.41.1 
  DNS  Server             :  192.168.77.20 
  Domain  Name            :  abc.efg.com 
 System Load Information 
  CPU  Used  Ratio         :  1% 
  Memory  Used  Size      :  36,429,824  bytes  (57%) 

Check the version of firmware on which the XG1200 is running and verify the system status based on CPU load and memory 
usage. 
 

6.1.3 Reviewing Log Messages 

Log messages about the XG1200 are classified into 4 levels -- CRITICAL, ERROR, WARNING, and INFO -- in accordance with 
the severity of events. 
To display event logs, run the "

show log

" command in the operator EXEC mode or in the administrator EXEC mode. 

 

Содержание XG1200



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды