manualshive.com logo in svg

Fujitsu XG1200, Руководство пользователя

Поделиться
Скачать
Fujitsu XG1200 Скачать руководство пользователя страница 232

XG1200 User's Guide 

232/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

 

A.2.4 

npm (Network Protocol Control: 3000-3299) 

Message 

IDSeverity 

Message/Explanation/Solution 

S3001 
INFO 

Cold Start or Warm Start. 

 

Explanation 

The system has been turned on. 

S3002 
INFO 

Link down %1$. (%2$) 

 

Explanation 

Port status has changed from a link up to a link down. 

 

[[Inserted string]]%1$: Information on port whose status changed to a link down. 

 

[[Inserted string]]%2$: Cause of link down. 

For details, refer to "Link Status Detail" in the "show interface" command. 

S3003 
INFO 

Link up %1$. 

 

Explanation 

Port status has changed to a link up. 
[[Inserted string]]%1$: Information on port whose status changed to a link up. 

S3004 
WARNING 

%1$ detected storm drop. 

 

Explanation 

Broadcast storm was detected. 

 

[[Inserted string]]%1$: Information on port that dropped broadcast frames. 

 

Solution 

There may be loop topology in the network. Review the network connections. 

S3005 
WARNING 

%1$ detected port security violation. 

 

Explanation 

A violating packet was detected with Port Security. 

 

[[Inserted string]]%1$: Information on the port that detected the violating packet. 

 

Solution 

Investigate the cause of receiving violating packets. 

S3006 
WARNING 

%1$ detected loopback alert. 

 

Explanation 

A packet loop was detected. 

 

[[Inserted string]]%1$: Information on the port that detected the loop. 

 

Solution 

There may be loop topology in the network. Review the network connections. 
Loopback alerts is detected when a destination MAC address of a received frame has been registered with the 
MAC address table where the receiving port is registered as a destination. So loopback alert can be detected 
even if there is no loop in the network. 

P3007 
WARNING 

Flow control was changed to 'only-receive' accompanied by supporting 15KB frame. 

 

Explanation 

Since the jumbo frame size was changed to a value over 15KB, the setting for flow control was changed to 
"only-receive". 
 

Solution 

If you do not want to set the flow control to "only-receive", the jumbo frame size must be less than 15KB long.

P3008 
WARNING 

Only 'only-receive' is permitted for flow control when 15KB frame is supported. %1$ 

 

Explanation 

If the jumbo frame size is over 15KB, the setting for flow control is restricted to "only-receive" only. 

 

[[Inserted string]]%1$: Port information 

 

Solution 

If you do not want to set the flow control to "only-receive", the jumbo frame size must be less than 15KB long.

P3009 
INFO 

%1$ has been attached to %2$. 

 

Explanation 

The physical port was attached to link aggregation. 

 

[[Inserted string]]%1$: Physical port information 

 

[[Inserted string]]%2$: Aggregation group information 

P3010 
INFO 

%1$ has been detached. 

 

Explanation 

The physical port was detached from link aggregation. 
[[Inserted string]]%1$: Information on physical port detached 

Содержание XG1200



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды