Fujitsu ROG30LMTA Скачать руководство пользователя

Страница: 55 / 80

Detective Actuators:

Detective details:

Forecast of Cause :

Check Point 3 : Check Outdoor Fan

Check Point 6 : Replace Main PCB

Check Point 1 :

Check connections of Outdoor Unit Electrical Components

Outdoor unit Main PCB

Compressor

1. Defective connection of electric components 2. Outdoor Fan Operation failure

3. Outdoor Heat Exchanger clogged 4. Compressor failure 5. Transistor PCB failure

6. Main PCB failure

Check if connector is removed.

Check if

the terminal connection

is loose.

Check erroneous connection.

Check if cable is open.

>>Upon correcting the removed connector or mis-wiring, reset the power.

Check Point 2 : Check Outdoor Fan, Heat Exchanger

Is there anything obstructing the air distribution circuit?
Is there any clogging of Outdoor Heat Exchanger?

Is the Fan rotating by hand when operation is off ?

>> If the Fan Motor is locked, replace it.

Check Outdoor Fan Motor. (Refer to Trouble shooting 29)

>> If the Fan Motor is failure, replace it.

Check Point 4 : Check Compressor

(PARTS INFORMATION 2)

Check Compressor.

If Check Point 1 5 do not improve the symptom, change Main PCB.

When more than normal operating current to IPM in Main PCB flows,

the compressor stops.

After the compressor restarts, if the same operation is repeated within 40sec,

the compressor stops again.

If and repeats 5 times, the compressor stops permanently.

02-22

Trouble shooting 19

OUTDOOR UNIT Error Method:
IPM Error

Check Point 5 : Check Transistor PCB

(PARTS INFORMATION 7)

Check

Transistor PCB.

Indicate or Display:

Indoor Unit :

Operation lamp: 6 times Flash,

Timer lamp : 5 times Flash

ERROR CODE : [E : 65]

Wired Remote Controller :

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание ROG30LMTA

















































































Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды

Fujitsu ROG30LMTA, Инструкция по эксплуатации

Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды