Fujitsu ROG30LMTA Скачать руководство пользователя

Страница: 19 / 80

20. DEFROST OPERATION CONTROL

01-17

1. CONDITION OF STARTING THE DEFROST OPERATION

The defrost operation starts when the outdoor heat exchanger temperature sensor (Tn) detects

the temperature lower than the values shown in Table19.

2. CONDITION OF THE DEFROST OPERATION COMPLETION

Defrost operation is released when the conditions become as shown in Table20.

( Table20 : Defrost Release Condition )

Release Condition

Outdoor heat exchanger temperature sensor value is higher than

+13°C

or Compressor operation time has passed 15 minutes.

( Table 19 : Condition of starting Defrost Operation )

1 time defrosting

after starting operation

Defrosting after 2 time

upon starting operation

Compressor integrating operation time

Less than 22 min.

22 to 62 min.

More than 62 min.

Does not operate

- 9°C

- 5°C

Less than 35 min.

More than 35min.

Does not operate

Integrating defrost

(Constant monitoring)

More than 240 min.

(For long continuous operation)

Less than 10min.*1

(For intermittent operation)

- 3°C

More than 215 min.

(For long continuous operation)

- 5°C

OFF count of the compressor

40 times.

*1 : If the compressor continuous operation time is less than 10 minutes, the OFF number of the compressor is counted.

If any defrost operated, the compressor OFF count is cleared.

Tn-Tn10 < - 5deg
Tn-Tnb < - 2deg
However, Tn < - 6°C

Tn10 : Temperature of continuous operation at 10minutes.

Tnb : Back 5minutes temperature

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание ROG30LMTA

















































































Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды

Fujitsu ROG30LMTA, Инструкция по эксплуатации

Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды