Fujitsu ROG30LMTA Скачать руководство пользователя

Страница: 20 / 80

01-18

Compressor OFF

Outdoor fan motor OFF

30 sec later four - way valve OFF

35 sec later compressor ON

3. Defrost Flow Chart

The defrosting shall proceed by the integrating operation time, outdoor temperature

and outdoor heat exchanger temperature as follows.

(Not defrosted for 10 minutes)

Heating operation start : Compressor ON

Outdoor heat exchanger temperature:

Over +13°C

Compressor ON time: Maximum 15 minutes

Defrost end

Compressor

integrating

operation:

Over 22 min.

Outdoor

heat exchanger

temperature:

Below - 9°C

Outdoor

heat exchanger

temperature:

Below - 5°C

Compressor

integrating

operation:

Over 35 min.

2nd and later defrost

Integrating defrost

(Constant monitoring)

Defrost Indicator:

[Operation lamp]

7 sec ON / 2 sec OFF

Defrost start

Tn-Tn10 < - 5deg

Tn-Tnb < - 2deg

However, Tn < - 6 °C

Compressor

OFF count :

40 times

(Less than 10min.)

1st defrost

Compressor

integrating

operation:

Over 62 min.

Compressor

integrating

operation:

Over 240 min.

Outdoor

heat exchanger

temperature:

Below - 3°C

Compressor

integrating

operation:

Over 215 min.

Outdoor

heat exchanger

temperature:

Below - 5°C

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание ROG30LMTA

















































































Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды

Fujitsu ROG30LMTA, Инструкция по эксплуатации

Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды