manualshive.com logo in svg

Fujitsu ROG30LMTA, Инструкция по эксплуатации

Поделиться
Скачать
Fujitsu ROG30LMTA Скачать руководство пользователя страница 36

02-03

2-1-2 WIRED REMOTE CONTROLLER DISPLAY (OPTION)

3-Wire

2-Wire

1. If an error occurs, an error icon appears on the “Monitor mode screen”.
    Touch the [Status] on the “Monitor mode screen”.The “Status” screen is displayed.

For the details of the indoor unit or outdoor unit error , refer to the error codes in each installation manual

2. Touch the [Error Information] on the “Status”screen. The “Error Information”screen is displayed.
    (If there are no errors, the [Error Information] will not be displayed.)

3. 2-digit numbers correspond to the error code in the table below. Touch the [Next page]
   (or [Previous page]) to switch to other connected indoor units.

1. Check the error

Mode

Set Temp.

Fri 10:00AM

Menu

Monitor

Back

Page 1/ 4

Page 1/ 5

Air Flow Direction

Economy

VT

Individual

Error Code

Address

[          1           ]

[ 02 01                                                                           ]

[   14 . 15, 41 .  44                                                         ]

[                       ]

[                 Off                 ]

Next
Page

Next
Page

Error
Information

Status

Status

Error Information

Fan

!

1.

2.

3.

If you use a wireless remote control,
the lamp onthe photo detector unit will output error codes by way of blinking patterns.

If you use a wired type remote control, error codes will appear on the remote control display.

See the lamp blinking patterns and error codes in the table. An error display is displayed only during running.

1 

ERROR DETECTION

This is possible only on a wired remote control.

If an error occurs, the following display will be shown.

(“Er” will appear in the set room temperature display.)

Remote control

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание ROG30LMTA

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды