Fujitsu ROG30LMTA Скачать руководство пользователя

Страница: 23 / 80

01-21

4. COOLING PRESSURE OVERRISE PROTECTION

When the outdoor unit heat exchange sensor temperature rises to 67°C or greater the compressor is

stopped and trouble display is performed.

5. HIGH TEMPERATURE AND HIGH PRESSURE RELEASE CONTROL ( HEATING MODE )

On heating mode, the compressor frequency is controlled as following based on the detection value of the indoor

heat exchanger temperature sensor.

Indoor heat exchange

temperature rises

Indoor heat exchange

temperature drops

[ Control System ]

It returns to the normal operation

Compressor is stopped

53°C

55°C

63°C

50°C

The compressor frequency is

decreased 2rps(30) every

120seconds.

The compressor frequency is

decreased 15rps(30) every

120seconds.

6. COMPRESSOR TEMPERATURE PROTECTION

When the compressor temperature sensor detects higher than

108°C, the compressor is stopped.

The protection is released when the compressor temperature sensor detects 80°C

after 3 minutes of compressor stop.

7. HIGH PRESSURE PROTECTION

When the pressure switch becomes OFF (Open : higher than 4.2 MPa),

the compressor is stopped.

It is released when the pressure switch becomes ON (Close : lower than 3.2 MPa)

after 3 minutes of compressor stop.

Stable zone

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание ROG30LMTA

















































































Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды

Fujitsu ROG30LMTA, Инструкция по эксплуатации

Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды