Fujitsu ROG30LMTA Скачать руководство пользователя страница 66

Страница: 66 / 80

02-33

Trouble shooting 30

OUTDOOR UNIT Error Method:

4-Way Valve Error

Detective Actuators:

Detective details:

Forecast of Cause :

Indoor unit Controller PCB

Heat Ex. temperature thermistor

Room temperature thermistor

4-way valve

When the indoor heat exchanger temperature is compared with

the room temperature, and either following condition is detected

continuously two times, the compressor stops.

1. Air filter clogged 2. Connector connection failure 3. Thermistor failure 4. Coil failure

5. 4-way valve failure 6. Controller PCB failure

Check Point 2 : Check connection of Connector

Check if connector is removed.

Check erroneous connection.

Check if thermistor cable is open.

>> Upon correcting the removed connector or mis-wiring, reset the power.

Check Point 4 : Check the solenoid coil and 4-way valve

Remove CN30 from PCB and check the resistance value of coil.

Resistance value is 2.085 (at 20°C).

>> If it is Open or abnormal resistance value, replace Solenoid Coil.

Cooling or Dry operation

[Indoor heat exchanger temp.] - [Room temp.] > 10degC
Heating operation

[Indoor heat exchanger temp.] - [room temp.] < -10degC

If the same operation is repeated 5 times, the compressor stops permanently.

[ Solenoid coil ]

Check each piping temperature,

and the location of the valve by the temperature difference.

>> If the value location is not proper, replace 4-way valve.

[ 4-way valve ]

Check Point 5 : Replace Controller PCB

If Check Point 1- 3 do not improve the symptom, replace Controller PCB.

Check Point 3 : Check each thermistor

Isn’t it fallen off the holder?

Is there a cable pinched?

>> Check characteristics of thermistor (Refer to Trouble shooting 11, 12),

If defective, replace the thermistor

Check Point 1 : Check the Air filter condition

Check is Air filter dirty.

>>If the Air filter dirty, clean up the Air filter.

Indicate or Display:

Indoor Unit :

Operation lamp: 9 times Flash,

Timer lamp : 9 times Flash

ERROR CODE : [E : 99]

Wired Remote Controller :

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание ROG30LMTA

















































































Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды

Fujitsu ROG30LMTA, Инструкция по эксплуатации

Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды