Fujitsu ROG30LMTA Скачать руководство пользователя

Страница: 17 / 80

15. MANUAL AUTO OPERATION (Indoor unit body operation)

If MANUAL AUTO Button is set, the operation is controlled as shown in Table15.

If the remote control is lost or battery power dissipated, this function will work without the remote control.

OPERATION MODE

Auto changeover

FAN CONT. MODE

Auto

TIMER MODE

Continuous (No timer setting available)

SETTING TEMP.

24°C

SETTING LOUVER

Standard

SWING

OFF

(Table15)

01-15

16. FORCED COOLING OPERATION

Forced cooling operation is started when pressing MANUAL AUTO button for 10 seconds or more.

During the forced cooling operation, it operates regardless of room temperature sensor.

Operation LED and timer LED blink during the forced cooling operation. They blink for 1 second ON

and 1 second OFF on both operation LED and timer LED (same as test operation).

Forced cooling operation is released after 60 minutes of starting operation.

The FORCED COOLING OPERATION will start as shown in Table16.

Manual auto operation

OPERATION MODE

FAN CONT. MODE

TIMER MODE
SETTING TEMP.
SETTING LOUVER

SWING

( Table16 )

Forced cooling operation

Cooling

Initial : Horizontal

(It is changed follow as setting of remote controller)
OFF

Room Temp is not controlled

If cooling operation is set, the operation is controlled as shown in Table16.

When the power was interrupted by a power failure, etc. during operation, the operation contents

at that time are memorized and when power is recovered, operation is automatically started with

the memorized operation contents.

When the power is interrupted and recovered during timer operation, since the timer operation time

is shifted by the time the power was interrupted, an alarm is given by blinking (7 sec ON/2 sec OFF)

the indoor unit body timer lamp.

[ Operation contents memorized when the power is interrupted ]

Operation mode

Set temperature

Set air flow

Timer mode and timer time

Set air flow Direction

Human sensor setting

Low noise operation

wing

ECONOMY operation

10°C HEAT operation

14. AUTO RESTART

At the time when the air conditioner is switched from the cooling mode to heating mode, the

compressor is stopped, and the four-way valve is switched in 3 minutes later after

the compressor stopped.

13. FOUR-WAY VALVE EXTENSION SELECT

This function is not available when the server room control is active

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание ROG30LMTA

















































































Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды

Fujitsu ROG30LMTA, Инструкция по эксплуатации

Результаты поиска

Содержание ROG30LMTA

Отзывы:

Похожие инструкции для ROG30LMTA

Бренды по названию

Популярные бренды