Fujitsu Primergy RX100 S3 Скачать руководство пользователя страница 179

Страница: 179 / 287

179

PRIMERGY RX100 S3 User’s Guide

Inst
allin
g I

nte

al O

pti

ons

Slide the server.

Pull the server forward until it stops.

While pressing the locks on both sides, pull out the server a little.

Pull out the server holding its back tightly to remove from the rack.

Loosen the screw on the rear of the server.

• When sliding the server or pushing it back, be careful not to pinch fingers or

clothes. Failure to do so may cause injury.

• If the server is pulled too much, it may fall and cause injury.

• When pulling out the server from the rack, make sure to hold the rear half of

the server. A spring inside the rail may cause the server to fall.

Lock

Hold the rear part

[Rear of the Server]

Содержание Primergy RX100 S3
































































































































































































































































































Результаты поиска

Содержание Primergy RX100 S3

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu Primergy RX100 S3, Руководство пользователя

Результаты поиска

Содержание Primergy RX100 S3

Отзывы:

Бренды по названию

Популярные бренды