Fujitsu AO* R09LECN Скачать руководство пользователя страница 23

Страница: 23 / 64

3. ANTIFREEZING CONTROL (Cooling and Dry mode)

The compressor speed is decreased on cooling & dry mode when the indoor heat exchanger
temperature sensor detects the temperature lower than 4

°C

Then, the anti-freezing control is released when it becomes higher than Release temperature A.

(Table 22 : Anti-freezing protection operation / Release temperature)

4. COOLING PRESSURE OVERRISE PROTECTION

When the outdoor unit heat exchange sensor temperature rises to

67°C

or greater,

the compressor is stopped.
Then the compressor will be restarted after 3 minutes ST.

5. HIGH TEMPERATURE RELEASE CONTROL ( HEATING MODE )

In heating mode, the compressor speed is controlled based on the detection value
of the indoor heat exchanger temperature sensor.

01-20

Outdoor temperature zone

A, B , C, D

7°C

13°C

Release temperature A

E, F

Indoor heat exchange
temperature rises

Indoor heat exchange
temperature drops

[ Control System ]

It returns to the normal operation

53°C

50°C

The compressor speed is
decreased 3rps every 60seconds.

5-1. HIGH TEMPERATURE RELEASE CONTROL of Outdoor Unit

Indoor heat exchange
temperature rises

Indoor heat exchange
temperature drops

[ Control System ]

It returns to the normal operation

55°C

52°C

5-2. HIGH TEMPERATURE RELEASE CONTROL of Indoor Unit

Refer to below

Compressor operation
57rps or more 55rps
35 ~ 55rps Rotational speed down every 120 sec
28 ~ 33rps 23rps
18 ~ 23rps OFF

[ ASYA09LEC ]

Compressor operation
48rps or more 45rps
39 ~ 45rps Rotational speed down every 120 sec
27 ~ 36rps 25rps
18 ~ 25rps OFF

[ ASYA12LEC ]

Содержание AO* R09LECN

































































Результаты поиска

Содержание AO* R09LECN

Отзывы:

Похожие инструкции для AO* R09LECN

Бренды по названию

Популярные бренды

Fujitsu AO* R09LECN, Инструкция по эксплуатации

Результаты поиска

Содержание AO* R09LECN

Отзывы:

Похожие инструкции для AO* R09LECN

Бренды по названию

Популярные бренды