Fujitsu AO* R09LECN Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 64

background image

15. MANUAL AUTO OPERATION (Indoor unit body operation)

ASYA09LEC

ASYA12LEC

780rpm

35rps

780rpm

39rps

17. COMPRESSOR PREHEATING

18. COIL DRY OPERATION CONTROL

The coil-dry operation functions by pressing COIL DRY button on the remote controller.
The coil-dry operation is consisted of Fan operation 50 minutes, Heating operation 3 minutes,
and Fan operates for 30 minutes at last before ending the air conditioner operation.

(Table 15 : COIL-DRY Operating Functions)

Indoor Fan Speed

Compressor
Frequency

Louver
Position

01-14

16. FORCED COOLING OPERATION

Forced cooling operation is started when pressing MANUAL AUTO button for 10 seconds or more.
During the forced cooling operation, it operates regardless of room temperature sensor.
Operation LED and timer LED blink during the forced cooling operation. They blink for 1 second ON
and 1 second OFF on both operation LED and timer LED (same as test run operation).
Forced cooling operation is released after 60 minutes of starting operation.
The FORCED COOLING OPERATION will start as shown in Table14.

When the outdoor heat exchanger temperature is lower than 5

°C

and the all operation has been

stopped for 30 minutes, power is applied to the compressor and the compressor is heated.
(By heating the compressor, warm air is quickly discharged when operation is started.)
When operation was started and when the outdoor temperature rises to 7

°C

or greater,

preheating is ended.

( Fig. 12 : Outdoor heat exchanger temperature )

ON

5°C

7°C

OFF

If MANUAL AUTO Button is set, the operation is controlled as shown in Table13.
If the remote control is lost or battery power dissipated, this function will work without the remote control.

OPERATION MODE

Auto changeover

FAN CONT. MODE

Auto

TIMER MODE

Continuous (No timer setting available)

SETTING TEMP.

24

°

C

SETTING LOUVER

Standard

SWING

OFF

(Table 13)

Manual auto operation

OPERATION MODE
FAN CONT. MODE
TIMER MODE
SETTING TEMP.
SETTING LOUVER
SWING

( Table 14)

Forced cooling operation

Cooling
Hi

Horizontal
OFF

Room Temp is not controlled

-

«
...
15
16
17
18
19
...
»

Содержание AO* R09LECN

































































Отзывы:

Нет отзывов

Похожие инструкции для AO* R09LECN

Бренд: Danby Страницы: 34

Бренд: Danby Страницы: 40

Бренд: Neffes Страницы: 20

Бренд: Kaisai Страницы: 168

Бренд: National Comfort Product Страницы: 32

Бренд: National Comfort Product Страницы: 28

Pinguino Air-to-Air PAC EL112CST

Бренд: DeLonghi Страницы: 8

GWC09NA-D3NNA3A/I

Бренд: Gree Страницы: 72

TAC-09CHSA/XA71

Бренд: TCL Страницы: 45

Бренд: NewAir Страницы: 104

Бренд: INVENTOR Страницы: 24

Бренд: ICP Страницы: 13

Бренд: Hitecsa Страницы: 19

Бренд: Nortek Страницы: 16

Бренд: Klarstein Страницы: 12

Comfort-Aire BD-101

Бренд: Heat Controller Страницы: 35

Бренд: Daikin Страницы: 14

Бренд: Verine Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды