Fujitsu AO* R09LECN Скачать руководство пользователя страница 2

Страница: 2 / 64

CONTENTS

1. DESCRIPTION OF EACH CONTROL OPERATION

1. COOLING OPERATION................................................................................................

3. DRY OPERATION.........................................................................................................

2. HEATING OPERATION.................................................................................................

5. INDOOR FAN CONTROL..............................................................................................

4. AUTO CHANGEOVER OPERATION............................................................................

7. LOUVER CONTROL.....................................................................................................

6. OUTDOOR FAN CONTROL..........................................................................................

9. TIMER OPERATION CONTROL...................................................................................

8. COMPRESSOR CONTROL..........................................................................................

11. TEST OPERATION CONTROL...................................................................................

10. ELECTRONIC EXPANSION VALVE CONTROL........................................................

13. FOUR-WAY VALVE EXTENSION SELECT................................................................

12. PREVENT TO RESTART FOR 3 MINUTES (3 MINUTES ST)...................................

15. MANUAL AUTO OPERATION (Indoor unit body operation).......................................

14. AUTO RESTART.........................................................................................................

16. FORCED COOLING OPERATION..............................................................................

18. COIL DRY OPEARTION CONTROL...........................................................................

17. COMPRESSOR PREHEATING..................................................................................

21. BASE HEATER OPERATION......................................................................................

01-01

01-02

01-03

01-04

01-05

01-07

01-08

01-09

01-10

01-13

01-14

01-15

22. DEFROST OPERATION CONTROL...........................................................................

24. VARIOUS PROTECTIONS..........................................................................................

23. OFF DEFROST OPERATION CONTROL...................................................................

01-16

01-18

01-19

01-13

2. TROUBLE SHOOTING

2-1 ERROR DISPLAY.......................................................................................................

2-1-1 INDOOR UNIT AND WIRED RMOTE CONTROLLER DISPLAY (OPTION)......

3. APPENDING DATA

2-1-2 WIRED REMOTE CONTROLLER DISPLAY (OPTION).....................................

2-2 TROUBLE SHOOTING WITH ERROR CODE............................................................

2-3 TROUBLE SHOOTING WITH NO ERROR CODE......................................................

02-01

02-02

02-03

02-24

2-4 SERVICE PARTS INFORMATION.............................................................................. 02-29

19. 10

°C HEAT OPERATION.................

...........................................................................

20. ECONOMY OPERATION............................................................................................

3-1 FUNCTION SETTING.................................................................................................

3-1-1 INDOOR UNIT....................................................................................................

3-1-2 Procedures to change the Function Setting for wireless RC..............................

03-01

03-03

3-2 Thermistor Resistance Values.................................................................................... 03-05

Содержание AO* R09LECN

































































Результаты поиска

Содержание AO* R09LECN

Отзывы:

Похожие инструкции для AO* R09LECN

Бренды по названию

Популярные бренды

Fujitsu AO* R09LECN, Инструкция по эксплуатации

Результаты поиска

Содержание AO* R09LECN

Отзывы:

Похожие инструкции для AO* R09LECN

Бренды по названию

Популярные бренды