Fujitsu AO* R09LECN Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 64

background image

4. AUTO CHANGEOVER OPERATION

When the air conditioner is set to the AUTO mode by remote control, operation starts in the optimum
mode from among the HEATING, COOLING, DRY and MONITORING modes. During operation, the
optimum mode is automatically switched in accordance with temperature changes. The temperature
can be set between

18°C

and

30°C

in

1°C

steps.

When operation starts, only the indoor and outdoor fans are operated for 1 minute. After 1 minute,
the room temperature and outdoor temperature are sensed and the operation mode is
selected in accordance with the table below.

C zone

32°C

B zone

-10°C

A zone

( Table.4 Operation mode selection table)

Outdoor temperature (TO)

Indoor room temperature (TB)

A zone

B zone

C zone

TB > TS+

2°C

Monitoring

Cooling

(automatic dry)

Cooling

(automatic dry)

TS+

2°C

TB

TS -

2°C

Monitoring

Monitoring

Monitoring

TB TS -

2°C

Heating

Heating

Monitoring

When COOLING was selected at

, the air conditioner operates as follow:

The same operation as COOLING OPERATION of item 1 above is performed.
When the room temperature has remained at (set temperature -

1°C

) for 8 minutes, operation is

automatically switched to DRY and the same operation as DRY OPERATION of item 3 above
is performed.
If the room temperature reaches (set tempe

2°C

during DRY operation, operation returns to

COOLING operation.

When HEATING was selected at , the same operation as HEATING OPERATION of item 2
above is performed.

When the compressor was stopped for 6 consecutive minutes by the temperature control function
after the COOLING or HEATING operation mode was selected at above, operation is switched
to MONITORING and the operation mode is selected again.

1

<

1

2

3

1

4

1

( Fig.4 : Outdoor temperature zone selection )

01-04

«
...
5
6
7
8
9
...
»

Содержание AO* R09LECN

































































Отзывы:

Нет отзывов

Похожие инструкции для AO* R09LECN

Бренд: ZIBRO CLIMA Страницы: 164

airconditioningcentre KFR-23IW/AG

Бренд: Martin Страницы: 17

Бренд: Enviracaire Страницы: 106

Aqu@Scop Advance R410A

Бренд: Airwell Страницы: 134

Бренд: MrCool Страницы: 27

Бренд: Daikin Страницы: 20

Бренд: Klimaire Страницы: 17

Бренд: AERMEC Страницы: 68

ProShield Plus Ai

Бренд: Oreck Страницы: 10

Бренд: TriStar Страницы: 72

MEGA-TEC W120AP

Бренд: Bard Страницы: 44

Бренд: GE Страницы: 48

Бренд: GE Страницы: 48

Бренд: Samsung Страницы: 73

Бренд: Fakir Страницы: 10

Бренд: Emerson Страницы: 12

Бренд: Emerson Страницы: 12

Бренд: Brezza Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды