Fujitsu AB*G30LRTE series Скачать руководство пользователя страница 25

Страница: 25 / 71

01-22

4. COOLING PRESSURE OVERRISE PROTECTION

When the outdoor unit heat exchange sensor temperature rises to 67°C or greater,

the compressor is stopped and trouble display is performed.

5. HIGH TEMPERATURE AND HIGH PRESSURE RELEASE CONTROL ( HEATING MODE )

On heating mode, the compressor frequency is controlled as following based on the detection value of the indoor

heat exchanger temperature sensor.

Indoor heat exchange

temperature rises

Indoor heat exchange

temperature drops

[ Control System ]

It returns to the normal operation

Compressor is stopped

53°C

55°C

63°C

50°C

The compressor frequency is

decreased 2rps every 120seconds.

The compressor frequency is

decreased 15rps every 120seconds.

6. COMPRESSOR TEMPERATURE PROTECTION

When the compressor temperature sensor detects higher than 108°C, the compressor is stopped.

The protection is released when the compressor temperature sensor detects 80°C

after 3 minutes of compressor stop.

7. HIGH PRESSURE PROTECTION

When the pressure switch becomes OFF (Open : higher than 4.2 MPa), the compressor is stopped.

It is released when the pressure switch becomes ON (Close : lower than 3.2 MPa)

after 3 minutes of compressor stop.

24. COMPRESSOR STOP CONTROL

When the detection value of outdoor temperature sensor is lower than Temp in the Table 22,

the compressor is stopped.

( Table 22 : Operation temperature of compressor stop control )

Temperature

AO* G30/ 36LETL

Cooling

Heating

-15°C

Stable zone

Содержание AB*G30LRTE series








































































Результаты поиска

Содержание AB*G30LRTE series

Отзывы:

Похожие инструкции для AB*G30LRTE series

Бренды по названию

Популярные бренды

Fujitsu AB*G30LRTE series, Инструкция по эксплуатации

Результаты поиска

Содержание AB*G30LRTE series

Отзывы:

Похожие инструкции для AB*G30LRTE series

Бренды по названию

Популярные бренды