Fujitsu AB*G30LRTE series Скачать руководство пользователя страница 37

Страница: 37 / 71

02-10

Trouble shooting 8

INDOOR UNIT Error Method:

Indicate or Display:

Indoor unit Fan Motor Error

Refer to error code table.

Detective Actuators:

Detective details:

Forecast of Cause:

Check Point 1 : Check rotation of Fan

Check Point 2 : Check ambient temp. around motor

Indoor unit Controller PCB

Indoor unit fan motor

1. Fan rotation failure 2. Fan motor winding open 3. Motor protection by surrounding temperature rise

4. Control PCB failure 5. Indoor unit fan motor failure

Rotate the fan by hand when operation is off.

(Check if fan is caught, dropped off or locked motor)

>>If Fan or Bearing is abnormal, replace it.

Check excessively high temperature around the motor.

(If there is any surrounding equipment that causes heat)

>>Upon the temperature coming down, restart operation.

When the condition that actual frequency of Indoor Fan is

below 1/3 of target frequency is continued more than 56 seconds.

Check Point 4 : Replace Controller PCB

If Check Point 1- 3 do not improve the symptom, replace Controller PCB.

Check Point 3 : Check Indoor unit fan motor

Check Indoor unit fan motor. (PARTS INFORMATION 4)

>>If Indoor unit fan motor is abnormal, replace Indoor unit fan motor.

Содержание AB*G30LRTE series








































































Результаты поиска

Содержание AB*G30LRTE series

Отзывы:

Похожие инструкции для AB*G30LRTE series

Бренды по названию

Популярные бренды

Fujitsu AB*G30LRTE series, Инструкция по эксплуатации

Результаты поиска

Содержание AB*G30LRTE series

Отзывы:

Похожие инструкции для AB*G30LRTE series

Бренды по названию

Популярные бренды