Fujitsu AB*G30LRTE series Скачать руководство пользователя страница 23

Страница: 23 / 71

22. OFF DEFROST OPERATION CONTROL

1. OFF DEFROST OPERATION CONDITION

When operation stops in the [Heating operation] mode, if frost is adhered to the outdoor unit heat

exchanger, the defrost operation will proceed automatically. In this time, if indoor unit operation

lamp flashes slowly (7 sec ON / 2 sec OFF), the outdoor unit will allow the heat exchanger to defrost,

and then stop.

In heating operation, the outdoor heat exchanger temperature is less than -4°C,

compressor continuous operation more than 10 minutes, and

compressor operation integrating time lasts for more than 30 minutes.

OFF Defrost Flow Chart

Heating operation stop

Outdoor heat exchanger temperature :

Below -4°C

Compressor continuous operation :

Over 10 minutes

Compressor integrating operation :

Over 30 minutes

Defrost start

Defrost Indicator:

[Operation lamp]

7 sec ON / 2 sec OFF

Outdoor heat exchanger temperature :

Over +13°C

Compressor ON time : Over 15 minutes

Defrost end

2. OFF DEFROST END CONDITION

Release Condition

Outdoor heat exchanger temperature sensor value is higher than +13°C or Compressor

operation time has passed 15 minutes.

01-20

Содержание AB*G30LRTE series








































































Результаты поиска

Содержание AB*G30LRTE series

Отзывы:

Похожие инструкции для AB*G30LRTE series

Бренды по названию

Популярные бренды

Fujitsu AB*G30LRTE series, Инструкция по эксплуатации

Результаты поиска

Содержание AB*G30LRTE series

Отзывы:

Похожие инструкции для AB*G30LRTE series

Бренды по названию

Популярные бренды