Fuji Xerox DocuCentre S1810 Скачать руководство пользователя

Страница: 157 / 202

Image Quality Problems

157

lem S

lving

The printout
contains white
areas, or white or
colored stripes.

The paper is damp.

Replace the paper with new paper.

The paper is unsuitable.

Load the correct type of paper.

The printout is
faint overall.

When using the Bypass tray
to print, the paper size
specified in the print driver
does not match the type and
size of the paper actually
loaded.

Load paper of the correct type and size in
the Bypass tray.

Refer to "Loading Paper in Bypass Tray"
(P.76).

Multiple pages were fed
through the machine at
once.

Riffle through the stack of paper thoroughly
before loading it.

The paper is
wrinkled.

The paper is unsuitable.

Replace the paper with new paper.

Paper has been added to
the paper loaded.

The paper is damp.

Text is blurry.

The paper is unsuitable.

Replace the paper with new paper.

Paper has been added to
the paper loaded.

The paper is damp.

White or color
patches appear
vertically.

The drum cartridge has
deteriorated or been
damaged.

Replace the drum cartridge with a new
one.

Refer to "Replacing the Drum Cartridge"
(P.142).

The toner cartridge has run
out of toner.

Replace the toner cartridge with a new
one.

Refer to "Replacing the Toner Cartridge"
(P.139).

Symptom

Possible Cause

Remedy

向

Paper feed

direction

Содержание DocuCentre S1810










































































































































































































Результаты поиска

Содержание DocuCentre S1810

Отзывы:

Похожие инструкции для DocuCentre S1810

Бренды по названию

Популярные бренды

Fuji Xerox DocuCentre S1810, Руководство пользователя

Результаты поиска

Содержание DocuCentre S1810

Отзывы:

Похожие инструкции для DocuCentre S1810

Бренды по названию

Популярные бренды