manualshive.com logo in svg

Frymaster BIELA14-T Series, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Frymaster BIELA14-T Series Скачать руководство пользователя страница 77

7-8 

Code 

ERROR MESSAGE 

EXPLANATION 

E53 

CAN BUS ERROR - CALL SERVICE 

Communications are lost between boards. 

E54 

USB ERROR 

USB connection lost during an update. 

E55 

SYSTEM INTERFACE BOARD 2 MISSING - CALL SERVICE 

SIB board 2 connection lost or board failure. 
 

E61 

MISCONFIGURED ENERGY TYPE 

The fryer is configured for the incorrect energy 
type. 

E62 

VAT NOT HEATING – CHECK ENERGY SOURCE – XXXF 
OR XXXC 

The vat is not heating properly. 

E63 

RATE OF RISE  

Rate of rise error occurred during a recovery test. 

E64 

FILTRATION INTERFACE BOARD FAILURE -  FILTRATION 
AND TOP OFF DISABLED - CALL SERVICE 

Filtration Interface Board connections lost or 
board failure. 

E65 

CLEAN OIB SENSOR – XXX F OR XXX C   - CALL SERVICE 

Gas  -The  oil  is  back  sensor  does  not  detect  oil.  
Clean oil sensor (see section 6.6.2).   

E66 

DRAIN VALVE OPEN – XXXF OR XXXC 

Drain valve is opened during cooking. 

E67 

SYSTEM INTERFACE BOARD NOT CONFIGURED - CALL 
SERVICE 

Controller is turned on when the SIB board is not 
configured. 

E68 

OIB FUSE TRIPPED – CALL SERVICE 

The  VIB board OIB fuse has tripped and didn’t 
reset. 

E69 

RECIPES NOT AVAILABLE – CALL SERVICE 

The controller has not been programmed with 
product recipes.  Replace controller with factory 
programmed controller. 

E70 

OQS TEMP HIGH  

Oil temperature is too high for a valid OQS 
reading. Filter at a temperature between 300ºF 
(149ºC) and 375ºF (191ºC). 

E71 

OQS TEMP LOW 

Oil temperature is too low for a valid OQS reading. 
Filter at a temperature between 300ºF (149ºC) and 
375ºF (191ºC). 

E72 

TPM RANGE LOW 

The TPM is too low for a valid OQS reading.  This 
may also be seen with fresh new oil.  The incorrect 
oil type may be selected in the setup menu. The 
sensor may not be calibrated for the oil type. See 
oil type chart in instruction document 8197316.  If 
issue continues contact a FAS. 

E73 

TPM RANGE HIGH 

The TPM reading is too high for a valid OQS 
reading.  Dispose the oil.   

E74 

OQS ERROR 

The OQS has an internal error. If issue continues 
contact a FAS. 

E75 

OQS AIR ERROR 

The OQS is detecting air in the oil. Check the O-
rings and check/tighten prescreen filter to ensure 
no air is entering the OQS sensor. If issue 
continues contact a FAS. 

E76 

OQS ERROR 

The OQS sensor has a communication error. Check 
connections to the OQS sensor. Power cycle the 
entire fryer battery.   If issue continues contact a 
FAS. 

 

 
 
 

Содержание BIELA14-T Series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды