Frymaster BIELA14-T Series Скачать руководство пользователя страница 73

Страница: 73 / 82

7-4

Problem

Probable Causes

Corrective Action

M4000 display shows

INSERT pan.

Filter pan is not fully set into fryer.

Missing filter pan magnet.

Defective filter pan switch.

Pull filter pan out and fully reinsert
into fryer. Ensure controller does
not display P.

Ensure the filter pan magnet is in
place and replace if missing.

If the filter pan magnet is fully
against the switch and controller
continues to display INSERT PAN,
switch is possibly defective.

Auto filtration won’t

start.

Oil level too low.

Oil temperature is too low.

Filter Pan out.

Filtration in recipe settings is set to
OFF.

Filter relay has failed.

Ensure oil level is at the top oil fill
line (at the top oil level sensor).

Ensure the oil temperature is at
setpoint.

Ensure controller does not display
P. Ensure the filter pan is fully
seated into fryer. Power cycle the
fryer.

Set filtration in recipes to ON.

Call your FAS for assistance.

Filter Pump runs, but

oil return is very slow.

Improperly installed or prepared filter
pan components.

Pre-filter screen may be clogged.

Remove the oil from the filter pan
and replace the filter pad/paper,
ensuring that the filter screen is in
place

under

the pad/paper.

Verify, if using a pad, that the rough
side is facing up.

Verify that O-rings are present and in
good condition on filter pan
connection fitting.

Clean pre-filter (see section 6.5.4).

Содержание BIELA14-T Series



















































































Результаты поиска

Содержание BIELA14-T Series

Отзывы:

Бренды по названию

Популярные бренды

Frymaster BIELA14-T Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BIELA14-T Series

Отзывы:

Бренды по названию

Популярные бренды