Frontier EGA/PY-3030D Скачать руководство пользователя страница 77

Страница: 77 / 83

7-6

Ver.1.36

7.4 LIST OF ERROR CODES FROM CONTROL SOFTWARE

ERRO NO./DISPLAY

CAUSE

SOLUTION/CHECK POINTS

1. Heater

Heater not powered

Check to see if the cable from the pyrolyzer is
properly connected to the POWER connector
located on the rear of controller.

2. Sensor

Abnormal input from sensor

[Furnace or Interface]
Make sure the cable from the pyrolyzer is
properly connected to the SENSOR connector
located on the rear of the controller.

[Cryo-Trap]
Ensure that the temperature sensor connector
is short-circuited when MicroJet Cryo-Trap is
not used.

3. Overheating

Overheated.

Make sure the cable from the pyrolyzer is
properly connected to the SENSOR connector
located on rear of the controller.

If this does not resolve the problem, it may be
heater failure (Furnace or Interface). Or it may
be a cooling fan failure (Sample cup stand by
position). Contact your nearest sales office.

4. COM Port

USB cable contact failure

Re-seat the USB cable at the PC

11. Connection

Connection failure to
Auto-Shot Sampler

(1) Ensure that the cable from Auto-Shot
Sampler is properly connected to RS-232C
connector on the rear of the controller.

(2) Make sure the Auto-Shot Sampler is
powered on.

12. Cup chute

Cup chute not attached to the
Auto-Shot Sampler.

Properly attach cup chute to Auto-Shot
Sampler.

13. Sample cup retrieval

Sample cups not properly
retrieved.

(1) Make sure supply pressure of gas reservoir
is 300 kPa

– 500 kPa.

(2) Ensure that the valve control cable from the
gas reservoir is properly connected to the rear
of the Auto-Shot Sampler.

(3) Make sure sample cups are not deformed.

21.Cryo-trap Temperature

MJT sensor not properly
cooled.

(1) While the thermal exchange coil is at room
temperature, make sure the pressure is 250

–

300 kPa when Cooling is turned ON.

(2) Make sure there is ample amount of liquid
nitrogen.

Содержание EGA/PY-3030D




















































































Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды

Frontier EGA/PY-3030D, Руководство по эксплуатации

Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды