Frontier EGA/PY-3030D Скачать руководство пользователя страница 15

Страница: 15 / 83

Ver.1.36

2 - 1

CHAPTER 2 SPECIFICATIONS

The system consists of the pyrolyzer furnace, which also serves as thermal desorption unit, and

temperature controller.

Multi-Shot pyrolyzer

EGA/PY-3030D

1. Performance guaranteed

(detector: MS)

See CHAPTER 8 of this manual for analytical conditions.

1. Reproducibility of pyrograms

2. Reproducibility of EGA

thermograms

Flash pyrolysis of PS (25 µg) at 550°C (Eco cup LF used), the coefficient of variation

(RSD) of the peak area ratio of styrene trimer (SSS) and methyl stearate (Me-Ste):

≤2%

(Eco cup LF, single cup used)

The coefficient of variation (RSD) of the peak top temperature of PS:

≤0.3%

2. Furnace and sampling unit

(Vertical micro furnace)



Pyrolyzer furnace

Sample introduction

Pyrolysis tube material

Temperature control range and

stability

Cooling system

Cooling time (pressure: 500kPa)

Cylindrical ceramic heater

Push-button to free-fall system with manual up/down-movement

Quartz

Room tempe 10°C up to 1,050°C (1°C step) / ±0.1°C

Forced air cooling by nitrogen or compressed air

Within 10 min (800°C down to 50°C when ITF in auto mode)



Interface (ITF)

Temperature/Stability

ITF needle

Cartridge heater

40 up to 450°C (1°C step) / ±0.1°C

Needle with side opening (inner surface deactivated by gradient multi-layer treatment)



Sampler

Double-Shot sampler

For Double-Shot and Single-Shot analyses

Liquid sampler

For introduction of liquid samples (regular 10 µL micro syringe can be used)



Sample cup

Eco cup SF (small)

Maximum capacity: 50 µL (deactivated stainless steel)

Eco cup LF (large)

Maximum capacity: 80 µL (deactivated stainless steel)

3. Temperature controller

PC control (PC not included)



Functions

SGL/DBL, Direct EGA, Heart-Cut EGA, ITF temp, Method File, Temp Monitor,

Maintenance

Other functions: control of Selective Sampler, MicroJet Cryo-Trap;, temperature

calibration, and Carrier Gas Selector



Temperature control range

Pyrolyzer furnace

30 up to 1,050°C (1°C step)

Ramp rate

600°C/min max (1°C step)

Hold time

0 up to 999.9 min (0.1 min step)

Pyrolysis time

0 up to 999.9 min (0.1 min step)

Interface

30 up to 450°C (1°C step) Auto/Manual control



Overheat protection temperature

PY: 1100°C, ITF: 500°C, Sample cup standby position: 100°C



Communication

USB 2.0

*: Prolonged operation of the pyrolyzer at a furnace temperature higher than 800°C will shorten the furnace heater life.

When operating at 800°C or higher, keep the operation time less than 20 minutes. If it is operated at 800°C or higher

for a prolonged period time, contact us at

[email protected]

. When the pyrolyzer is in a standby state, we

recommend that the furnace temperature should be kept below 200°C. This will extend the furnace heater life.

Содержание EGA/PY-3030D




















































































Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды

Frontier EGA/PY-3030D, Руководство по эксплуатации

Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды