Frontier EGA/PY-3030D Скачать руководство пользователя страница 22

Страница: 22 / 83

3 - 4

Ver.1.36

3.5 CONNECTING TEMPERATURE CONTROLLER

3.5.1 Connecting power cable to outlet

Use only a power outlet with a ground terminal and correct voltage specified. Required power can be

found near the power cable connector on the rear panel of the temperature controller.

Also, ensure that the power requirement for the pyrolyzer is met by checking the pyrolyzer rear

panel.

3.5.2 Connecting control PC

Connect the temperature controller to your PC using the supplied USB cable (2 m long). The control

software for the pyrolyzer is independent from GC or GC/MS control software, and it does not

exchange data with other instrument.

3.5.3 Hooking up remote signal cable

Use the remote signal cable to connect the temperature controller to your GC. Through this cable,

the temperature controller receives

“Ready” signal from the GC, and sends “GC START” signal back

to the GC.

3.6 CONNECTING COOLING GAS LINE

3.6.1 About cooling gas

Nitrogen or compressed air is normally used as a cooling gas. Since the gas passes through high

temperature surfaces, it should not contain oil or moisture. The purity of the gas does not directly

influence analytical results.

3.6.2 Connecting temperature controller and pyrolyzer

Use the supplied vinyl tubing to connect the gas outlet to the temperature controller then the

temperature controller to the pyrolyzer.

The cooling gas is automatically controlled and is consistent with the pyrolyzer temperature settings

and with the temperature program.

This product uses compressed air or nitrogen for cooling the
pyrolyzer furnace. Ensure that you have a good ventilation if nitrogen
gas is used. There is a risk of suffocation, if it is used in a confined
area with poor ventilation.

WARNING

Содержание EGA/PY-3030D




















































































Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды

Frontier EGA/PY-3030D, Руководство по эксплуатации

Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды