Frontier EGA/PY-3030D Скачать руководство пользователя страница 34

Страница: 34 / 83

4-5

Ver.1.36

4.2.1.3 Using air as atmosphere gas

In this section, analysis in an air atmosphere is described. In this analysis, the sample is first heated

in air; the carrier gas is then switched to helium in order to purge air from the column and detector. If

the analysis is automated using the AS-1020E Auto-shot sampler, the MicroJet Cryo-Trap

(MJT-1030Ex, MJT-1035E) and Selective Sampler (SS-1010E) are required. In addition, the Carrier

Gas Selector (CGS-1050Ex) is highly recommended. The procedure for performing an automated

sequence of analysis in air is described below. Manual operation requires in-depth professional

knowledge and extensive experiences. Contact us if assistance is needed ([email protected]).

(1)

“Check” the checkboxes for MicroJet cryo-Trap and Selective Sampler - see Fig. 4.5.

(2) If using an automated Carrier Gas Selector, select

“Air” as shown in Fig. 4.5(a). If a Carrier Gas

Selector is not used or if manual control is used, select

“Air” as shown in Fig. 4.5(b).

(3)

“He Purge Time” (C) in Fig. 4.5(a) is the time it takes for the Carrier Gas Selector to completely

purge the helium in the Pyrolyzer with air. Normally the default value (1.0 min) is used.

(4)

“He Purge Time in Column” (D) is the time it takes to completely replace the helium in the

column with air. Normally 2.0 min is used.

(5)

“Air Purge Time in GC/MS” (E) is the time it takes to completely purge the air in the column and

detector with helium after the sample has completed the heating process. In particular, if a mass

spectrometer is used as a detector, air in the mass spectrometer must be completely purged

before turning on the filament. If this is the case, use a default value of 7.0 min, although this

time is somewhat dependents on the MS model.

Fig. 4.5 Accessory device set-ups when analysis is being done in an air atmosphere.

(a) Automatic control of Carrier gas selector.

(b) Automatic control of Carrier gas selector not in use.

When performing a pyrolysis in air, air is used as a carrier gas. Be sure
to allow a long purging time to completely replace air with inert gas
such as helium, before raising the oven temperature.

CAUTION

Содержание EGA/PY-3030D




















































































Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды

Frontier EGA/PY-3030D, Руководство по эксплуатации

Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды