Frontier EGA/PY-3030D Скачать руководство пользователя страница 78

Страница: 78 / 83

Ver.1.36

8-1

CHAPTER 8 GUARANTEE OF BASIC PERFORMANCE

(REPRODUCIBILITY)

In a GC pyrolysis system, the path from the pyrolyzer to the detector via the separation column is very

important. Every element in the system (i.e., the pyrolyzer, interface, GC injection port, separation

column, detector crossover and detector) plays an important role in the reproducibility of the data.

Reproducibility (expressed as the %RSD of three sequential analyses) of the polystyrene EGA

thermogram and the polystyrene pyrogram are guaranteed to meet the following specifications:

Evolved Gas Analysis: Frontier Laboratories guarantees that the reproducibility of the apex of the

polystyrene peak is

≤0.3% RSD.

Pyrolysis: Frontier Laboratories guarantees that the reproducibility of the peak area ratio between

methyl stearate, added as internal standard, and the styrene trimer (SSS) is

≤2% RSD.

The analytical conditions and typical chromatograms are shown in Figures 8.1 and 8.2.

There is a risk of burn injury.

Since the pyrolyzer furnace can be very hot, ensure that the protective housing

cover is properly placed on the pyrolyzer.

CAUTION

HOT

When using solvents, wear protective gears such as safety goggles

and work only in a well-ventilated area free of ignition sources.

The ends of separation column and eco stick are very sharp. When

handling these items, wear safety goggles for your safety.

CAUTION

Содержание EGA/PY-3030D




















































































Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды

Frontier EGA/PY-3030D, Руководство по эксплуатации

Результаты поиска

Содержание EGA/PY-3030D

Отзывы:

Похожие инструкции для EGA/PY-3030D

Бренды по названию

Популярные бренды