Fronius 4,044,008 Скачать руководство пользователя страница 32

Страница: 32 / 136

Signal descrip-
tions

Pin

Signal

Signal description

Torch body sensor 1

The respective torch body is deposited in the
corresponding torch body rack

Torch body sensor 2

Torch body sensor 3

Torch body sensor 4

Torch body sensor 5

Torch body sensor 6

Torch body sensor 7

Torch body sensor 8

Torch body sensor 9

Torch body sensor 10

Robacta TX sensor 1 cover Signal only available as an option.

Robacta TX cover 1 is open

Robacta TX sensor 2 cover Signal only available as an option.

Robacta TX cover 2 is open

Robacta TX valve 1 cover

Signal only available as an option.
-

opens and closes a Robacta TX cover

Robacta TX valve 2 cover

Signal only available as an option.
-

opens and closes a Robacta TX cover

'C-Act. 3' signal 1

Reserve signal for actuator

Slide signal

Signal only available as an option.
-

torch body has been deposited in the Ro-
bacta TX slide / Robacta TX slide XL

Wire sensor signal

Verification whether the wire electrode pro-
trudes from the torch body after a successful
change of the torch body.

'C-Sens. 4' signal 2

Reserve signal for sensor

'C-Sens. 4' signal 1

Reserve signal for sensor

Pressure switch signal

Compressed air supply to torch body change-
over station is OK.
The signal is output in a range of 12.5 - 13 bar.

Change torch body valve 1

NOTE!

Switch the valve via a relay,

as the current input of the valve is at
least 500 mA.

Activates the torch body change

Reserve relay OUT

Reserve signal for actuator (relay contact)

'C-Sens. 5' signal 1

Reserve signal for sensor

Clamp gas nozzle and
cleaning motor on / Start
cleaning

Signal only available as an option.

"Clamp gas nozzle and cleaning motor on" sig-
nal for Robacta Reamer V only:
-

activates the gas nozzle clamping device
and the cleaning motor

"Start cleaning" signal for Robacta Reamer de-
vices (except for Robacta Reamer V), Robacta
TC devices:
-

activates the cleaning process

Содержание 4,044,008









































































































































Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды

Fronius 4,044,008, Руководство по эксплуатации

Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды