Fronius 4,044,008 Скачать руководство пользователя страница 88

Страница: 88 / 136

Troubleshooting

Torch body unexpectedly loses contact with the torch body coupling during gas
purging

Cause:

Gas purging pressure too high

Remedy:

Adjust gas purging pressure

Torch body unexpectedly loses contact with the torch body coupling during gas
purging

Cause:

Gas hole in centre bolt dirty

Remedy:

Clean gas hole in centre bolt - see "Cleaning the gas hole" section in the op-
erating instructions

After a torch body has been changed, there is some residual coolant on the torch
body

Cause:

Coolant hoses incorrectly connected to the cooling unit

Remedy:

Connect the coolant hoses to the cooling unit in the right direction for the cool-
ant flow

After a torch body has been changed, there is some residual coolant on the torch
body

Cause:

Torch body coupling worn

Remedy:

Send the torch body coupling to the manufacturer's service department

After a torch body has been changed, there is some residual coolant on the torch
body

Cause:

Robot speed too fast when picking up and setting down the torch body

Remedy:

Reduce robot speed when picking up and setting down the torch body

After a torch body has been changed, there is some residual coolant on the torch
body

Cause:

Compressed air escaping from the torch body coupling is causing coolant to
be blown out of the set down torch body when locking the torch body coupling

Remedy:

Lock the torch body coupling next to the torch body changeover station

After the torch body has been set down, coolant sprays out of the torch body

Cause:

Torch body very hot

Remedy:

Use water-cooled gas nozzle

RCU 5000i outputs the error message "No coolant flow"/power source outputs the
error message "no | H2O"

Cause:

Cooling unit flow watchdog has been triggered

Remedy:

Set filter time for flow watchdog to 25 seconds using RCU 5000i

Torch body coupling does not open

Cause:

Compressed air supply to torch body changeover station briefly too low

Remedy:

Change torch body manually (see operating instructions, "Manually changing
the torch body" section)

Torch body coupling does not open

Cause:

Very long hosepacks

Remedy:

Increase pressure to max. 1.6 MPa (= 16 bar = 232.06 psi) for the com-
pressed air amplifier

Содержание 4,044,008









































































































































Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды

Fronius 4,044,008, Руководство по эксплуатации

Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды