Fronius 4,044,008 Скачать руководство пользователя страница 40

Страница: 40 / 136

Application example

Application ex-
ample

NOTE!

Irrespective of the overall welding system setup

adhere to the compressed air specifications

provide the compressed air supply to the wire-feed unit and the torch body
changeover station as shown

(1)

Compressed air supply line 5.50 -
6.00 bar (79.77 - 87.02 psi)

(10) Torch body changeover station with

interface

(2)

Compressed air supply line for
wire-feed unit max. 6.00 bar (87.02
psi)

(11) Data cable

(3)

Wire-feed unit

(12) Robot

(4)

Junction valve

(13) Drum coil

(5)

Compressed air supply line from
torch body changeover station to
torch body coupling on the robot 13
bar (174.05 psi)

(14) Power source with cooling unit

(6)

Hosepack with torch body coupling
and Robacta TX torch body

(15) Power source interface

(7)

Compressed air maintenance unit
with filter

(16) Data cable

(8)

Compressed air supply line for
torch body changeover station 5.50
- 6.00 bar (79.77 - 87.02 psi)

(17) Robot control

(9)

Y-distributor

(1)

(2)

(4)

(5)

(10)

(8)

(9)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(3)

(6)

(7)

Содержание 4,044,008









































































































































Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды

Fronius 4,044,008, Руководство по эксплуатации

Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды