Fronius 4,044,008 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 136

background image

94

Maintenance for each torch body service, at least

weekly

Preparation

When carrying out the following work, position the robot arm so that

-

the Unlock/Lock button on the torch body changeover station can be pressed with
one hand

-

the torch body can be removed from or placed onto the torch body coupling with
the other hand

Feed out the wire electrode from the hosepack
Hold torch body with one hand
Press the Unlock/Lock button on the torch body changeover station

-

torch body coupling lock opens

Remove torch body from the torch body coupling
Depressurise the compressed air line of the torch body changeover station and make
sure that this compressed air line remains depressurised for the duration of the work
on the device
Disconnect the compressed air line from compressed air connection "A" on the torch
body changeover station

Press and hold the Unlock/Lock button on the torch body changeover station until
compressed air no longer emerges from compressed air connection "A" on the torch
body changeover station

-

compressed-air booster unit in the torch body changeover station discharges

De-energise the torch body changeover station

Safety

CAUTION!

Risk of injury from escaping compressed air from compressed air

connection "A". Compressed air emerges at up to 16 bar (232.06 psi) from com-
pressed air connection "A" when the Unlock/Lock button is pressed. While com-
pressed air is emerging from compressed air connection "A":
-

wear ear protection

-

keep the face and all other body parts away from compressed air connection
"A"

-

ensure that no other persons are in the vicinity of the torch body changeover
station

1

2
3
4

5
6

7

8

9

CAUTION!

Risk of injury from compressed air escaping unintentionally. The torch

body changeover station must remain depressurised and de-energised until all
work is completed.

«
...
92
93
94
95
96
...
»

Содержание 4,044,008









































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4,044,008

Бренд: PACIFIC CYCLE Страницы: 112

Бренд: E+E Elektronik Страницы: 14

Бренд: E+E Elektronik Страницы: 26

Бренд: E+E Elektronik Страницы: 28

Бренд: E+E Elektronik Страницы: 2

Бренд: BW Страницы: 8

Бренд: EarthX Страницы: 17

Бренд: EarthX Страницы: 23

Бренд: Yealink Страницы: 6

Бренд: Zagg Страницы: 2

Canon C100 Z-Finder

Бренд: Zacuto Страницы: 14

DS-KABD8003-RS3

Бренд: HIKVISION Страницы: 3

Maintenence Kits

Бренд: Generac Power Systems Страницы: 1

Бренд: IAG Страницы: 3

Бренд: Prorack Страницы: 14

Бренд: Polaroid Страницы: 64

Бренд: SRAM Страницы: 26

Бренд: Gamko Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды