Frigidaire LGUB2642LF2 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 187

background image

Basic Information

1-4

Important Safety Instructions

Safety Precautions

Do not attempt to install, operate or service the unit until
you have read the safety precautions in this manual.
Safety items throughout this manual are labeled with a
Danger, Warning, or Caution based on the risk type.

Definitions

This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury or
death.

General Safety

•

Do not store or use gasoline or other flammable

liquids near this or any other appliance. Read product
labels for warnings regarding flammability and other
hazards.

•

Do not operate the refrigerator in the presence of explo-
sive fumes.

•

Avoid contact with any moving parts of the automatic
ice maker.

•

Remove all staples from the carton to avoid injury.
Staples can also damage finishes if they come in contact
with other appliances or furniture.

Child Safety

Packing Materials:

• Packing cartons covered with rugs, bedspreads,

plastic sheets, or stretch wrap may become airtight
chambers and can quickly cause suffocation.

• Destroy or recycle the product’s carton, plastic bags,

and any other exterior wrapping material immediately
after the refrigerator is unpacked. Children should
never play with these items.

Child Entrapment and Suffocation:

• These problems are not limited to the past. Whether

junked, abandoned, or temporarily stored (even for a
few hours), unattended refrigerators and freezers are
dangerous. Please take the precautions listed below.

Proper Disposal of Refrigerators/Freezers

Electrolux Home Products Inc. strongly encourages
responsible appliance recycling/disposal methods.
Check with your utility company or visit www.recyclemy-
oldfridge.com for more information on recycling your old
refrigerator.

Before you recycle or dispose of your old refrigerator/
freezer:

• Remove the doors.

• Leave the shelves and baskets in place so children

may not easily climb inside.

• Have refrigerant and compressor oil removed by a

qualified service technician.

DANGER

INDICATES AN IMMINENTLY

HAZARDOUS SITUATION WHICH, IF NOT AVOIDED,
WILL RESULT IN DEATH OR SERIOUS INJURY.

WARNING

INDICATES A POTENTIALLY

HAZARDOUS SITUATION WHICH, IF NOT AVOIDED,
COULD RESULT IN DEATH OR SERIOUS INJURY.

CAUTION

indicates a potentially hazardous situ-

ation which, if not avoided, may result in minor or
moderate injury.

Indicates installation, operation, or maintenance
information which is important but not hazard
related.

«
...
4
5
6
7
8
...
»

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

Бренд: Waeco Страницы: 344

Бренд: VWR Страницы: 26

Бренд: VOX electronics Страницы: 100

Бренд: Jenn-Air Страницы: 65

Бренд: ROMMER Страницы: 14

Бренд: Indesit Страницы: 12

Бренд: Danby Страницы: 16

Бренд: Laurus Страницы: 128

Бренд: Avanti Страницы: 21

Бренд: Telefunken Страницы: 40

Бренд: Randell Страницы: 4

Бренд: Siegbert Страницы: 54

Бренд: NEFF Страницы: 119

Бренд: Haier Страницы: 36

Бренд: Haier Страницы: 81

Бренд: Haier Страницы: 116

Бренд: Haier Страницы: 31

HRF-450D 6 Series

Бренд: Haier Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды