Frigidaire LGUB2642LF2 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 187

background image

4-5

31
32

Test 57C: Evaporator Fan Test
To start this interactive test, touch ‘power on-off’ to
activate the fan. Touching ‘power on-off’ again will turn
the fan off. The Freezer display shows current state of
the fan “on” or “OFF”.
Test 58C: Ice Level Sensor Test
NOTE: Test will start automatically when you enter or
pass test 58.
The ice bucket must be removed from the ice maker
chamber prior to entering this test. The ice maker motor
will run turning the tray and lowering then resetting the
bail arm continually until you exit the test. If the bail arm
is allowed to fall freely, the tray will return to the home
position and no alarm will sound. If you hold the bail arm
up as the tray rotates (thus simulating the presence of
a full ice bucket), then the alarm will sound as the tray
returns to home position.
Unless both conditions are met, the test is considered
failed.

Test 63C: Tray twist test
(See Flow Chart Test #58C)
The ice bucket must be removed from the ice maker
chamber prior to entering this test. Start the test by
pushing ‘power on-off’. The ice maker motor will run
turning the tray. You should see a “1” in the freezer
display and the “GOOD” light should come on if the test
passes. If the “1” and the “GOOD” light does not come
on, the test is failed. The test will run continuously until
you press ‘power on-off’ or change to another test.

Temperature Resistance Chart For

Negative Temperature Coefficient

Thermistors

Ice Maker (Flex Tray Fresh Food Compartment)

«
...
47
48
49
50
51
...
»

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

Бренд: U-Line Страницы: 12

Бренд: U-Line Страницы: 24

Бренд: Randell Страницы: 2

Бренд: Randell Страницы: 20

Бренд: Randell Страницы: 2

Бренд: YATO Страницы: 108

Бренд: Smeg Страницы: 16

Бренд: Gaggenau Страницы: 96

Бренд: Omcan Страницы: 16

Бренд: Giostyle Страницы: 96

Бренд: Goddess Страницы: 84

Бренд: Zero Appliances Страницы: 5

Бренд: GE Страницы: 63

Бренд: GE Страницы: 48

RH29H9000SR/AA-03

Бренд: Samsung Страницы: 93

Бренд: Samsung Страницы: 58

Бренд: Candy Страницы: 143

Бренд: JUNO Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды