Frigidaire LGUB2642LF2 Скачать руководство пользователя страница 13

Страница: 13 / 187

Installation Information

2-1

CAUTION

Do Not install the refrigerator where the temperature

will drop below 55°F (13°C) or rise above 110°F

(43°C). The compressor will not be able to maintain

proper temperatures inside the refrigerator.
Do Not block the toe grille on the lower front of your

refrigerator. Suffi cient air circulation is essential for the

proper operation of your refrigerator.

This Use & Care Guide provides general installation and

operating instructions for your model. We recommend

using a service or kitchen contracting professional to

install your refrigerator. Use the refrigerator only as

instructed in this Use & Care Guide. Before starting

the refrigerator, follow these important fi rst steps.

Location

• Choose a place that is near a grounded, non-GFCI,

electrical outlet. Do Not use an extension cord or

an adapter plug.

• If possible, place the refrigerator out of direct

sunlight and away from the range, dishwasher, or

other heat sources.

• The refrigerator must be installed on a fl oor that is

level and strong enough to support a fully loaded

refrigerator.

• Consider water supply availability for models

equipped with an automatic ice maker.

Installation

• Allow the following clearances for ease of

installation, proper air circulation, and plumbing

and electrical connections:

Sides & Top

3/8 inch (9.5 mm)

Back

1 inch (25.4 mm)

Door opening

Your refrigerator should be positioned to allow easy

access to a counter when removing food. For best use of

refrigerator drawers and freezer baskets, the refrigerator

should be in a position where both can be fully opened.

Required Tools

You will need the following tools:

NOTE

If your refrigerator is placed with the door hinge side

against a wall, you may have to allow additional space

so the door can be opened wider.

NOTE

The refrigerator doors are designed to shut by

themselves within a 20 degree opening.

Содержание LGUB2642LF2




























































































































































































Результаты поиска

Содержание LGUB2642LF2

Отзывы:

Похожие инструкции для LGUB2642LF2

Бренды по названию

Популярные бренды

Frigidaire LGUB2642LF2, Руководство по обслуживанию

Результаты поиска

Содержание LGUB2642LF2

Отзывы:

Похожие инструкции для LGUB2642LF2

Бренды по названию

Популярные бренды