Frigidaire LGUB2642LF2 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 187

background image

6-37

Component Teardown

Compressor Area Mounting Tray

To access the compressor and inverter, condenser
and fan assembly, or to service the sealed system, it
may require that the compressor area mounting tray be
removed from the bottom of the unit. The mounting tray
is secured with four #2 square bit screws to the bottom
of the unit and two screws to the lower rear corners of
the cabinet.

To remove the compressor area mounting tray:

1. Unplug unit from wall outlet.

2. Pull unit from its installation and block unit up high

enough to access the four bottom screws. Have
on hand blocks to support the mounting tray as the
screws are removed. Several 6 inch pieces of 2” x 4”
lumber work well. See Caution Note.

3. Extract the four bottom screws securing the mounting

tray to the rear of the unit. (See Figure 6-101)

4. Extract the two screws securing the mounting tray to

the rear of the unit.

5. Drop mounting tray down to provide better access

to the grounding screws and sealed system compo-
nents.

Condenser Fan Assembly Removal

The condenser fan assembly is secured to the rear of the
compressor area with two bolts to the compressor mounting
plate. The compressor area mounting tray does not need to
be dropped to remove the fan assembly.

To remove the condenser fan assembly:

1. Pull unit from its installation position and unplug from

wall outlet.

2. Extract the screws securing the compressor shield to

the unit frame and remove from unit.

3. Disconnect wire leads to condenser fan motor at

Molex™ connector.

4. Extract the three bolts securing the fan assembly to the

condenser mounting brackets. (See Figure 6-102)

5. Pull fan motor assembly from unit, then pull fan

blade from motor shaft.

6. Remove the condenser fan shroud by extracting the

two 3/8” bolts securing the shroud to the mounting
tray.

When accessing the compressor area mounting tray, it is
recommended to have two people to block the unit high
enough to access the bottom screws.

The unit is heavy, make sure unit is secure when in the
blocked position. The unit should not rock or tip when on
blocks.

If the unit should tip or fall from the blocks while extracting
the screws, personal injury could occur and/or damage the
unit or the customers personal property.

If unsure about the safety of this operation, do not
continue. Contact your Regional Service Quality Manager
for assistance.

Compressor Area Mounting Tray

Bottom Screws

Ground
Screws

Power Cord

Inverter

Screw

Screw

Figure 6-101.

Figure 6-102.

Screws

Electrical

Connection

«
...
141
142
143
144
145
...
»

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

Бренд: Caldura Страницы: 8

Бренд: Cafe Страницы: 80

Бренд: McCall Страницы: 2

Бренд: Marvel Страницы: 1

Бренд: Galaxy Страницы: 64

Бренд: Ravanson Страницы: 51

Бренд: Saba Страницы: 20

SKIVIEW INTEGRAL WL

Бренд: Bonnet Neve Страницы: 70

Бренд: La Germania Страницы: 16

Silhouette Select SSBC056D1B

Бренд: Danby Страницы: 28

Бренд: Daewoo Страницы: 68

Бренд: Saba Страницы: 5

Бренд: White-Westinghouse Страницы: 32

Бренд: Igloo Страницы: 6

Бренд: RAMTONS Страницы: 15

Бренд: Scandomestic Страницы: 53

Бренд: Magic Chef Страницы: 12

Бренд: Saivod Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды