Frigidaire LGUB2642LF2 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 187

background image

Installation Information

2-8

Door Handle Mounting Instructions for Frigidaire Professional®

1 Remove handles from carton and any other protective packaging.
2 Position fresh food handle end over upper and lower pre-installed shoulder bolts (A) that are fastened into door,

ensuring the holes for the set screws are facing towards the opposite door.

3 While holding handle fi rmly against door, fasten upper and lower Allen set screws (B) with supplied Allen

wrench.

4 Repeat steps 2 and 3 to install opposite handle. Ensure the holes for the set screws are facing towards the fi rst door.
5 Position freezer handle end over left and right pre-installed handle mounts that are fastened to the door,

ensuring the holes for the set screws are facing down.

6 While holding handle fi rmly against door, loosely tighten far right Allen set screw (B) with supplied Allen wrench until there

is no gap between handle and door.

  7  Still holding the handle fi rmly to the door, fi rmly tighten far left Allen set screw (B) with supplied Allen wrench.
  8  Return to the far right Allen set screw (B) and fi rmly tighten with supplied Allen wrench.
  9  Firmly tighten the inside Allen set screws.

Í

NOTE

All set screws should be tightened so the screw is below the surface of the handle. The handles should be drawn

tight to freezer and refrigerator doors with no gaps. Opening the opposite door while tightening the Allen screw

makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this happens, tighten the set screws on the

handles.

Mounting Refrigerator Handles

Mounting Freezer Handle

«
...
18
19
20
21
22
...
»

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

Бренд: GE Страницы: 92

Бренд: Candy Страницы: 47

Бренд: Samsung Страницы: 466

Бренд: JUNO Страницы: 32

Бренд: Avanti Страницы: 2

Бренд: Carimali Страницы: 20

Бренд: Gorenje Страницы: 28

Бренд: Bauknecht Страницы: 13

PSH25MSSASV and

Бренд: GE Страницы: 124

Бренд: Lec Страницы: 28

Бренд: Philco Страницы: 146

Бренд: Freggia Страницы: 32

Бренд: Bauknecht Страницы: 14

Бренд: Panasonic Страницы: 60

Бренд: Zanussi Страницы: 12

Бренд: Zanussi Страницы: 16

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды