manualshive.com logo in svg

Frigidaire LGUB2642LF2, Руководство по обслуживанию

Скачайте бесплатно сервисное руководство для холодильника Frigidaire LGUB2642LF2 на нашем сайте. Этот мануал поможет вам разобраться в работе устройства и произвести ремонт при необходимости. Не забудьте загрузить его с manualshive.com.

Поделиться
Скачать
background image

Electronic Control

 3-7

Entering System Service Mode

Note:  Fresh Food Ice Maker service mode is discussed 
in section 4 of this manual.
Express-Select™
To enter the service mode, press and hold the freezer 
up (

∧

) and down (

∨

) temperature pads simultaneously 

for up to ten (10) seconds.  
Press Fresh Food up (

∧

) to advance thru the menu 

options; press ‘power on-off’ to initiate the selected test.
Pro-Select™
To enter the service mode, press and hold ‘control lock’ 
and ‘options’ simultaneously for up to ten (10) seconds.
Press ‘+’ on the LCD display to advance thru the menu 
options; press ‘power on-off’ to initiate the selected test.

Deactivation

Express-Select™
Press and hold the fresh food up (

∧

) key for up to ten 

(10) seconds.  The control will beep and service mode 
will deactivate.
Pro-Select™
Press and hold ‘+’ on the LCD display for up to ten (10) 
seconds.  The control will beep and service mode will 
deactivate.
NOTE: Service Mode automatically deactivates after 5 
minutes of no key entry. 

Tests

The test number will appear in the fresh food display.
When ‘power on-off’ is pressed, test results will appear 
in the freezer display. Refer to the troubleshooting guide 
for diagnostic flow charts.
Test 28:  Dispenser paddle test. 
Ensure the fresh food door is closed.  Display will show 
“ON” when paddle is pressed;  “OFF” when released.
Test 1:  Standard compressor test.
Push  ‘power on-off’ and the compressor will run.  Push 
‘power on-off’ again to stop.
NOTE: This test will not show when product has a VCC
Compressor.  VCC models use test 38.
Test 2:  Defrost heater test.
Push  ‘power on-off’ and the heater will come on. 
Push  ‘power on-off’ again and the heater will go off.
Test 3:  Fresh food compartment lighting test.
Push ‘power on-off’, then open the fresh food door and 
the fresh food compartment lights will come on low and 
ramp up. Push ‘power on-off’ again to cancel test.

Test 8:  Water valve (water dispenser test only)
NOTE:  Place a cup in the dispenser prior to starting this 
test to collect the water as both primary and dispenser 
valve will be activated. 
Push ‘power on-off’ to actuate valve.  Push ‘power on-off’ 
again to deactivate.
Test 9:  Freezer compartment lighting test.
Push the ‘power on-off’, then open the freezer door and the 
freezer compartment lights will come on low and ramp up.  
Push ‘power on-off’ again to cancel test.
Test 10:  Auger motor
Push  ‘power on-off’ to activate.  Auger runs with fresh food 
door closed.  Push ‘power on-off’ again to deactivate.
also,  Auger motor switch
Push  ‘power on-off’ to activate.  Auger stops when fresh 
food door switch is allowed to open.
Test 11:  Cube/Crush solenoid

Test 11:  Cube/Crush solenoid  
Push  ‘power on-off’ to activate. Solenoid pulls in.  Push 

Push  ‘power on-off’ to activate. Solenoid pulls in.  Push 
‘power on-off’ again to deactivate.  

‘power on-off’ again to deactivate.  
Note: The solenoid should only be activated momentarily 

Note: The solenoid should only be activated momentarily 
to prevent damage.  Do not leave the solenoid in activated 

to prevent damage.  Do not leave the solenoid in activated 
state for an extended period of time.

state for an extended period of time.
Test 12:  VCC condenser Fan
Push ‘power on-off’ or ‘+’ and the fan motor will run at 
full speed. Push ‘power on-off’ or ‘+’ again and it will stop 
running. 
NOTE: Only used with VCC Compressor.
Test 38:  VCC compressor 
Push ‘power on-off’ and the compressor will run at full 
speed.  Push ‘power on-off’ again and it will stop running.
NOTE: Only used with VCC Compressor.  Standard 
Compressor model uses test 1.
Test 15:  Evaporator fan
Push ‘power on-off’ and the fan will run at low speed. 
“LOW” will show in freezer display.  Push ‘power on-off’ and 
the fan will run at full speed.  “HI” will show in the freezer 
display.  Push ‘power on-off’ again and the fan will stop 
running and “Off” will show in the freezer display.
Test 22:  Damper test
Push ‘power on-off’.  The damper will open and “OP” will 
show in freezer display.  Push ‘power on-off’ again.  The 
damper will close and “CL” will show in the freezer display. 
Test 36:  Ice door test; ice chute door micro-switch 
only.
Displays “OP” when flapper is opened manually.
also, Ice door test; ice chute door solenoid & micro-
switch  
Push ‘power on-off’.  Dispenser and the solenoid will 

Push ‘power on-off’.  Dispenser and the solenoid will 
activate.  The Freezer display will show  “OP” 

activate.  The Freezer display will show  “OP” 

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

Gaggenau RC462704 Instruction Manual preview
RC462704
Бренд: Gaggenau Страницы: 81
Gaggenau RC472700 - annexe 2 Manual preview
RC472700 - annexe 2
Бренд: Gaggenau Страницы: 60
Gaggenau RC 200 Instructions For Use Manual preview
RC 200
Бренд: Gaggenau Страницы: 77
Gaggenau RB 472 Installation Instruction preview
RB 472
Бренд: Gaggenau Страницы: 33
Gaggenau RB 472 Operating Instructions Manual preview
RB 472
Бренд: Gaggenau Страницы: 82
Gaggenau RB 289 User Manual preview
RB 289
Бренд: Gaggenau Страницы: 36
Gaggenau RB 472 Operating Instrucctions preview
RB 472
Бренд: Gaggenau Страницы: 87
Gaggenau RC 462 Use & Care Manual preview
RC 462
Бренд: Gaggenau Страницы: 53
Off Indel B SLIM Series Instructions For Use Manual preview
SLIM Series
Бренд: Off Indel B Страницы: 128
essentiel b ERCVE200-60b1 Instruction Manual preview
ERCVE200-60b1
Бренд: essentiel b Страницы: 118
Igloo FR171 Instruction Manual preview
FR171
Бренд: Igloo Страницы: 12
Beverage-Air VM12 Installation And Operation Manual preview
VM12
Бренд: Beverage-Air Страницы: 10
Iceco STEEL VL60S Series Manual preview
STEEL VL60S Series
Бренд: Iceco Страницы: 24
Thetford MRFT415 Owner'S Manual preview
MRFT415
Бренд: Thetford Страницы: 7
Igloo KING IGL 20 User Manual preview
KING IGL 20
Бренд: Igloo Страницы: 15
Jenn-Air JRTDE228 Use And Care Manual preview
JRTDE228
Бренд: Jenn-Air Страницы: 23
STATESMAN TNF3500W Instruction Manual preview
TNF3500W
Бренд: STATESMAN Страницы: 16
Indesit IN TSZ 16 Series Operating Instructions Manual preview
IN TSZ 16 Series
Бренд: Indesit Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды