Frigidaire LGUB2642LF2 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 187

background image

7-17

Sealed System

DO NOT unbraze old filter-drier from system. This
will vaporize and drive moisture from desiccant
back into system. The old filter-drier should be cut
out of system.

Ice Maker Jumper Tube Replacement
Flex Tray Ice Maker Models

Always use the TORCH GUARD heat shield part
number 5304418872, behind evaporator before
attempting to solder. The excessive heat from
soldering will warp the plastic liner.

This unit has one heat exchanger (Suction Line & Cap
Tube Assembly) enclosed in the insulation between
the liner and the cabinet back. It has a Jumper tube
running from the out let of the ice maker compartment
evaporator to the inlet of main evaporator in the freezer
compartment. Because of this, the original part can
not be removed. There is a service kit to bypass the
internal jumper tube. It will be necessary to run a new
jumper tube down the back of the product and bypass
the internal jumper tube if the jumper tuber has a leak or
is restricted.

Jumper tube Kit Contains:

1- Jumper Tube 6- Screws
1- Filter-Drier

1- Cover

1- Armor Flex

1- Package Permagum

2- Tape

1- Instruction Sheet

1. Heat Shield

To replace the ice maker Jumper tube:

1.   Disconnect refrigerator from electrical supply.
2.   Remove all freezer section shelves.
3.   Remove evaporator cover.
4.   Disconnect wiring harness at liner plug.
5.   Follow tho instructions on pages 6-26 and 6-27 to

gain excess to the ice maker evaporator.

6. Cut the ice maker discharge line in front of the weld

and cut the line off even with the food liner.

7. Using a 1/4” drill bit, drill hole through cabinet from

inside just above the original heat exchanger.

8. Using a 1/2” drill bit, open hole drilled in Step 7 to

1/2” from back of product.

9. Place a heat shield between the food liner and the

ice maker evaporator.

10. Remove stubs of old Jumper tube from

evaporator and install new heat exchanger into
evaporator.

11. Push jumper tube through hole in cabinet.

and connect jumper tube to ice maker evaporator.

12. Slide Armor-Flex over jumper tube until cover is

against hole at back of cabinet.

13. Seal the hole on the inside and outside using
permagum.
14. Remove freezer door, baskets and evaporator

cover.

15. Disconnect jumper tube in front of the inlet line weld

of the freezer evaporator.

16. Cut off jumper tube at freezer liner.
17. Drill a 1/2 inch hole through cabinet next to old
jumper

tube.

18. With the heat shield in place remove stub from the

inlet line of the freezer evaporator

19. Insert new jumper tube through liner, connect to

inlet of the freezer evaporator and weld in place.

20. Seal bottom holes with permagum.
21. The one piece cover can now be installed over heat

exchanger. Place open end of cover with top of

compressor compartment opening. Attach cover to

back of cabinet using screws provided. There is no

need to predrill holes as the screws are self cutting.

22. Replace filter-drier using caution to connect cap

tubes properly as described in the filter-drier

replacement

section.

23. Evacuate and recharge system.
24. Bend remaining tubing to fit into machine

compartment opening, being careful not to set up

any excess noise from line vibration.

25. Run product to make sure refrigerant is circulating.
26. Reinstall evaporator and machine compartment

cover.

«
...
159
160
161
162
163
...
»

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

Бренд: Blomberg Страницы: 78

Бренд: Silver King Страницы: 17

Бренд: Norcold Страницы: 29

Бренд: Estate Страницы: 40

Бренд: U-Line Страницы: 39

Бренд: Orbegozo Страницы: 30

Бренд: Danby Страницы: 48

Бренд: Electrolux Страницы: 7

Бренд: Electrolux Страницы: 2

Бренд: KRAFT Страницы: 18

Бренд: Electrolux Страницы: 2

Бренд: Kenmore Страницы: 6

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 16

4433 - Pro 23.1 cu. Ft

Бренд: Kenmore Страницы: 27

4542 - Elite 23.1 cu. Ft. Refrigerator

Бренд: Kenmore Страницы: 24

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды