Frigidaire LGUB2642LF2 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 187

background image

6-36

Component Teardown

Mold Heater Removal

To remove the mold heater:

1. Disconnect refrigerator from electrical supply.

2. Remove the ice maker from freezer compartment.

3. Remove front cover.

4. Remove ice stripper.

5. Remove three screws that attach mounting plate to

support housing.

6. Remove three screws that attach mold to support

housing.

NOTE: One of the three screws is attached to the two
green/yellow ground wires and another one is holding
the clamp in place. The third screw is located in the lower
right corner of the support housing.

5. Unscrew wire nut holding three black leads

together and separate them.

NOTE: One black lead is connected to the mold
heater. Another is connected to the thermostat and
the third lead goes to the hold switch.

6. Disconnect remaining mold heater lead connected

to brown motor lead and black thermal cut-out lead.

7. Separate mold from support housing.

NOTE: Be careful not to destroy the thermostat gasket
located between the mold and support housing.

8. Remove hex head screw holding ice maker leveling

bracket to mold.

NOTE: The mold is crimped in six places, holding the
mold heater fi rmly in the mold groove. It may be

necessary to use a hammer and screwdriver to

remove the heater from the mold groove.

9. Use a flat-bladed screwdriver to pry inoperative

heater from mold groove.

10. Clean remaining thermal mastic sealer from

mold groove.

11. Apply layer of thermal mastic sealer to mold groove.

12. Install replacement mold heater.

13. Replace parts in reverse order. Ensure that

thermo-

stat gasket is in place. Bond the thermostat
to mold with thermal mastic sealer.

NOTE: For best operation, the freezer temperature
should be between -2°F to +4°F.

Compressor Area Components

Water Valve Removal

The water valve is secured to the rear of the unit with
two bolts to the lower right cabinet frame.

To remove the water valve:

1. Turn off water supply to water valve.

2. Remove the compression nut and ferrule from the water

valve inlet. (See Figure 6-100)

3. Remove water line exiting the water valve.

4. Disconnect electrical leads from water valve.

NOTE: Non-dispenser models will have a single water valve
mounted in the same manner as the four coil valve. The
water valve will have only one electrical connection to the
unit wire harness.

5. Extract the two bolts from the cabinet frame securing

the water valve in position.

Figure 6-100.

Water Valve

Inlet

Mounting

Screws

Yellow Coil

Dispenser

Blue Coil

Freezer

Ice maker

Green Coil

Fresh Food

Ice Maker

Beige Coil

Water Filter

Four Coil Valve Used On Dispenser Models

Single Coil Valve Used on Non-Dispenser Models

Water Valve

Inlet

Water Valve Inlet

Green Coil

«
...
140
141
142
143
144
...
»

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

Бренд: Amica Страницы: 88

Бренд: Hoover Страницы: 32

Бренд: Vitara Страницы: 26

Бренд: Igloo Страницы: 10

Бренд: Dometic Страницы: 49

Бренд: Dometic Страницы: 92

Бренд: Randell Страницы: 2

Бренд: VOX electronics Страницы: 61

Бренд: point Страницы: 80

Бренд: ZANKER Страницы: 40

Бренд: Hoshizaki Страницы: 10

Бренд: Samsung Страницы: 48

Бренд: Samsung Страницы: 108

Бренд: Samsung Страницы: 272

Бренд: Samsung Страницы: 272

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 60

Бренд: Samsung Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды