manualshive.com logo in svg

Frigidaire LGUB2642LF2, Руководство по обслуживанию

Скачайте бесплатно сервисное руководство для холодильника Frigidaire LGUB2642LF2 на нашем сайте. Этот мануал поможет вам разобраться в работе устройства и произвести ремонт при необходимости. Не забудьте загрузить его с manualshive.com.

Поделиться
Скачать
background image

 4-15

Test 55C:  Water Valve Test (continued)

After ice mold arrival to “Freeze” position, or if the mold 
was already in the “ Freeze” position, the Test ID stops 
flashing and the ice maker will turn on the water solenoid 
valve and the city water solenoid valve for a duration of 
four (4) seconds 
Water can be dispensed into a 4 oz. cup placed or held 
under the ice maker water spout (typically 80 ml).   Only 
one water dispensing 4 second cycle is allowed after the 
test is started.  Additional ON/OFF key activations are 
ignored.

Test 56C:  Finger Evaporator Heater Test
(See Flow Chart Test #56C)
To start this interactive test, touch the ON/OFF key to 
activate the heater.  The heater is turned Off 
automatically after 60 seconds.  Touching the ON/OFF 
key again will turn the heater Off.  The Freezer display 
shows the heater current state “on” or “OFF”.

Test 57C:  Evaporator Fan Test
(See Flow Chart Test #57C)
To start this interactive test, touch the ON/OFF key to 
activate the fan.  Touching the ON/OFF key again will 
turn the fan Off.   The Freezer display shows current 
state of the fan “on” or “OFF”.

Test 58C:  Ice Level Sensor Test
(See Flow Chart Test #58C)
Interactive test with audio.
This test has the requirement that the ice bucket be 
removed from the ice maker chamber prior to entering 
this test.  Also, if the ice mold is in the “Fill” position 
there can be no ice on the evaporator fingers.
Start the test by pushing the ON/OFF key.  The ice maker 
controller drives the mold to the Freeze position if it is 
not already there.  The Freezer will display ice maker 
sensor status “OFF”, indicating that the bale arm is in its 
lower position.  Manually raise the bale arm and observe 
the display changing status to “on” with repeatable audio 
continuously sounding “wrong Key” alarm as long as the 
switch is “on”.  Let the arm go back down and the display 
will change back to “OFF”  with no sound.
NOTE:  To verify sensor switch, manually push and
release the switch plunger.  See “OFF” and “on” (with 
sound) displayed accordingly.

Test 59C:  “Fill” Limit Switch Test 
(See Flow Chart Test #59C)
Interactive test with audio
Upon entering the test, the ice mold position is checked.  
If is not already in “Freeze” position, the mold is driven 
to “Freeze”.  The Freezer display will show the current 
status of the “Fill” limit switch, which should be “OFF”.   
Remove the ice maker cover for better switch access.  
Activate the switch manually to observe the “on” status 
displayed on the Freezer display and hear the audio 
alarm (See test 58C).  Release the switch and display will 
change to ‘OFF”  with no sound.

Test 60C:  “Freeze” Limit Switch Test
(See Flow Chart Test #60C)

Interactive test with audio.
Upon entering the test, ice mold position is checked.  If 
is not already in the “Fill”  position the mold is driven 
to the “Fill” position.   The Freezer display will show the 
current status of the “Freeze” limit switch, which should 
be “OFF”.  Remove the ice maker cover for better switch 
access.  Activate the switch manually to observe the “on” 
status displayed on Freezer display and hear the audio 
alarm (See test 58C).  Release the switch and display will 
change to ‘OFF” again with no sound.

Test 61C:  Ice Maker Evaporator Heater Test
(See Flow Chart Test #61C)
Interactive.
Pull the cartridge heater out of the ice maker assembly 
before staring this test.  The electric wires are to be 
connected and the ambient air temperature less then 
48°F in order for bi-metal in-line switch to remain closed.   
Touch the ON/OFF key to activate the heater.  Verify 
manually if the heater is working.  Touching the ON/OFF 
key again will turn the heater Off.  The Freezer display 
shows the heater current state “on” or “OFF”.

Test 62C:  EEV Test
(See Flow Chart Test #62C)
Automated.
Touch the ON/OFF key to start the test.  When waiting 
for the automated test result, the Fresh Food display will 
be flashing the test ID and the Freezer display will be 
showing the TH3 current temperature. (The ice maker 
controller will fully open the EEV and wait 120 seconds 
for the TH3 temperature to drop off a minimum 2°F).  
After the delay, the test result is displayed on the Freezer 
display as “P” for “Pass” or “F” for “Fail”.

Ice Maker (Finger Evaporator Fresh Food Compartment)

Содержание LGUB2642LF2




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LGUB2642LF2

GE ENERGY STAR GBS22HBS Dimensions And Installation Information preview
ENERGY STAR GBS22HBS
Бренд: GE Страницы: 2
GE CustomStyle GSC23LSRSS Dimension Manual preview
CustomStyle GSC23LSRSS
Бренд: GE Страницы: 3
GE CustomStyle GSC23LGR Dimensions And Installation Information preview
CustomStyle GSC23LGR
Бренд: GE Страницы: 3
GE Cafe CSHS5UGXSS Dimensions And Installation Information preview
Cafe CSHS5UGXSS
Бренд: GE Страницы: 2
GE 25 Use And Care Manual preview
25
Бренд: GE Страницы: 20
GE CZS25TSESS Owner'S Manual & Installation Instructions preview
CZS25TSESS
Бренд: GE Страницы: 120
GE CSHS6UGZSS Owner'S Manual And Installation preview
CSHS6UGZSS
Бренд: GE Страницы: 112
GE 18, 19 Owner'S Manual & Installation Instructions preview
18, 19
Бренд: GE Страницы: 48
GE 18, 19 Use And Care & Installation Manual preview
18, 19
Бренд: GE Страницы: 92
Camco 18 Owner'S Manual preview
18
Бренд: Camco Страницы: 36
Panasonic NR-AF162SNMY Operating Instruction preview
NR-AF162SNMY
Бренд: Panasonic Страницы: 8
ETNA KCV143WIT Instructions For Use Manual preview
KCV143WIT
Бренд: ETNA Страницы: 116
Insignia NS-CF17BK6 User Manual preview
NS-CF17BK6
Бренд: Insignia Страницы: 20
New Air NGF Series User Manual preview
NGF Series
Бренд: New Air Страницы: 10
Dometic miniBar RH 429LDAG Operating Instructions Manual preview
miniBar RH 429LDAG
Бренд: Dometic Страницы: 60
Smeg SR610X User Manual preview
SR610X
Бренд: Smeg Страницы: 18
Scandomestic SKS 192 W User Manual preview
SKS 192 W
Бренд: Scandomestic Страницы: 53
Estate 2316077B Use & Care Manual preview
2316077B
Бренд: Estate Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды