FRÄNKISCHE profi-air 250/360 flex Скачать руководство пользователя страница 81

Страница: 81 / 108

Installation and operating instructions profi-air 250/360 flex

8.2.2 Fault clearance E1 to E2 fans

To correct the fault, profi-air flex has to be opened in a “live” state which may be done by authorised and

qualified personnel only. In addition, applicable local regulations and safety provisions must be complied

with.

Replacement of the control board and/or fans is to be carried out by authorised and qualified personnel

and in the “dead” state of the device only. In addition, applicable local regulations and safety provisions

must be complied with.

Error message fans

Error message integrated control panel

flashing red LED

flashes once / extract air fan

flashes two times / supply air fan

profi-air cockpit app or wireless remote control error message

E1 / extract air fan

E2 / supply air fan

Unhinge the filter cover

Remove the device cover

Remove the control board cover

Fans properly

connected

to the

J6 and J16 and J7 and J17

clamps? Check connection

for broken cable

and corrosion

Yes

Note:

Select “Manual operation” and

“Ventilation mode 3” to carry out the following

measurements.

Connect the fans properly

Replace fan

Replace control board

Cut the

voltage supply

Cut the

voltage supply

Cut the

voltage supply

Are 230 VAC

applied to the fan?

Check the J6 and J7

clamps on the

control board

Yes

Содержание profi-air 250/360 flex













































































































Результаты поиска

Содержание profi-air 250/360 flex

Отзывы:

Похожие инструкции для profi-air 250/360 flex

Бренды по названию

Популярные бренды

FRÄNKISCHE profi-air 250/360 flex, Инструкция по установке и эксплуатации

Результаты поиска

Содержание profi-air 250/360 flex

Отзывы:

Похожие инструкции для profi-air 250/360 flex

Бренды по названию

Популярные бренды