manualshive.com logo in svg

Fraco SEH 4500, Сборка и руководство по эксплуатации, Страница: 56 / 69

Поделиться
Скачать
Fraco SEH 4500 Скачать руководство пользователя страница 56

     Construction Hoist                                                                Fraco SEH Premium Range

 

Assembly and Operating Manual 

Page 56 of 69 

doc no. 98030718-01  

11.7 Annual servicing 

  Check gear oil, fill up if necessary. Observe the external operating manual in the system. 

Gear oil recommendation: 

- 

  Aral 

Degol BG 220 

- 

  ESSO  Spartan EP 220 

- 

  BP 

Energol GR-XP 100 

- 

  Quantity approx. 1.8 litres per drive 

  Check gear rack is secure. 

- 

  197 Nm tightening torque. 

 
 

11.8  Servicing every 3 years 

The Fraco over speed safety brake may only be repaired or adjusted by the manufacturer's 
service technicians or his trained and authorized representatives. 
 
The over speed safety brake has been type-tested and must be replaced every 3 years or 
checked by the manufacturer or an authorized representative of the manufacturer. 
 
Change SYNTHETIC OIL every three/four years. 
Watch out! You must not mix the mineral and synthetic oils when refilling oil! 
 

 
11.9 Hoist lubrication 

 
It is carried out according to the "Lubrication diagram" and Figure 8.1. 
 

Lubrication diagram 

 

  Lubricating                

 

 

Number

   spot                                                

           of spots 

Lubricant

Method 

Monthly (40 hours) 

  1. Rack  

grease containing graphite  

coating 

  2. Safety device bearings                          

 

1 

grease* 

grease gun 

  3. Pinion bearings 

grease 

grease gun 

  4. Gear Shaft bearings 

grease

grease gun

Every 3 months (120 hours) – in addition to the above mentioned

  5. Cage door wire ropes and their suspensions  

4      grease  

coating  

  6. Door balance counterweight rails  

 

             4 

grease 

coating 

  7. Roof hatch hinges                                    

 

2 

oil 

oil can  

  8. Pins of landing bars and gates (doors) 

oil  

oil can   

Every year (480 hours) – in addition to the above mentioned

  9. Guide rollers                                

                        16 

grease  

grease gun 

10. Supporting rollers                                 

 

2 

grease 

grease gun 

11. Pulley wheels of wire ropes                 

 

4 

grease 

refill 

12. Pins of base enclosure door locking device 

grease  

refill 

13. Pins of cage door locking devices 

grease  

refill 

Every three years (1440 hours) – in addition to the above mentioned

14. Gearboxes                                  

 

 

2 

gear oil  
– see notice 

refill (2x) 

 

NOTE 

 

 

* . . . grease specification – see Safety device technical data 98030763. 

Содержание SEH 4500






































































Отзывы:

Нет отзывов