Model D2424LVmkII Reference Manual (Preview Function)
68
[AUTO PUNCH IN] key
[AUTO RTN END] key
[CLIPBOARD OUT] key
[AUTO PUNCH OUT] key
[AUTO RTN START] key
[CLIPBOARD IN] key
Operation
Memory key
Time base
ABS or MTC
BAR/BEAT/CLK
Flashing
Shuttle dial
(clockwise)
Flashing
Shuttle dial
(counter clockwise)
Executing the Preview function
(1)
Press the desired memory key while holding
down the [SHIFT] key when the recorder is
stopped.
Pressing the desired memory key will enable you
to preview the sound at the locate point (edit point)
stored in the corresponding memory key.
The recorder plays the fall (fade
out) of the sound at the locate
point stored in the keys.
The recorder plays the fall (fade
in) of the sound at the locate
point stored in the keys.
(2)
Adjust the monitor sound of the selected track
so that it can be monitored on the mixer.
<Note>:
If data stored in each memory key is
in the initial state, all memory keys will be in
ABS time 00H 00M 00S. In other words, the
program head value is in the memory. Should
fade out preview be executed in this condition,
the “
Void Data!
” message and memory data “
00H
00M 00S
” will alternately flash in the display as
a warning. However, for fade in preview, this
will function as the memory data “
00H 00M 00S
”
point.
(3)
Press the [STOP] button or the [EXIT/NO] key.
Trimming the sound while previewing
You can trim the position of the locate point (edit point) using the
Jog
dial while you preview the
sound. At this time, you can also adjust the size of the trimming steps (the amount of offset
controlled by the Jog dial).
Trimming allows you to fine-tune the position of the locate point stored in the memory keys
while previewing the sound. Use this function to change the Auto Punch In/Out points, the start
point of Copy & Paste and Move & Paste, and the start and end points of the Erase function.
<Notes>
• You can audition the result of trimming during the next preview. That is, if you trim the position while
previewing the sound for the first time, you can check the result when you preview the sound next time.
• If the locate point is shifted outside the range of the preview playback as a result of trimming, “
Void Data!
”
and the locate point indication appear alternately. In this case, you cannot use the Preview function. Trim
the position again so that it will be within the playback range.
• When Auto Punch mode is turned on and you trim the Auto Punch In or Auto Punch Out point while
previewing the sound with “
Void Data!
” indicated on the display, Auto Punch mode will be cancelled.
(4)
Trim the position at the selected unit (digit).
(5)
Press the [STOP] button or the [EXIT/NO] key.
The trimmed locate point (edit point) data will be
stored in the corresponding memory key.
(1)
Start previewing the sound by following the steps
described on the previous page.
(2)
Use the Jog dial to trim the position.
When previewing starts, the unit of Jog trimming
flashes on the screen.
For example, value of
SF
(sub-frame) flashes if ABS
Time Base or MTC Time Base is selected.
CLK
(clock) flashes if BAR/BEAT/CLK is selected.
The flashing value also indicates the position you
can trim.
(3)
To change the unit of trimming, turn the Shuttle
dial.
F
S
M
H
∞
42
OL
0
30
24
18
12
9
6
3
kHz
FS
CLOCK
BIT
SF
INT
1
24
∞
42
OL
0
30
24
18
12
9
6
3
LOCATE
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
∞
42
OL
0
30
24
18
12
9
6
3
kHz
FS
CLOCK
BIT
INT
1
24
∞
42
OL
0
30
24
18
12
9
6
3
CLK
BAR
LOCATE
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
SF
H
M
S
F
SF
H
M
S
F
CLK
BAR
CLK
BAR
