Model D2424LVmkII Reference Manual (Chain Play function)
63
Setup of the Chain Play Mode
<Important>:
Be sure the Chain Play List is set up correctly before setting the chain play mode. Each
setting of the chain play mode except “
Off
,” will not function if the previously mentioned “
Chain play
list
” is not set up correctly beforehand. If the mode is executed while set up of with an incorrect list,
after displaying “
Illegal P.List!
,” the D2424LVmkII will automatically go to the previously mentioned
“
Chain Play List?
” menu.
<Note>:
The chain play mode setting will be held even though power is switched off, and if power is
switched when the D2424LVmkII is set to pause mode, the recorder will automatically execute chain
play. If chain play is no longer required, reset to “
Off”
the “
Chain Play?
” menu after ending chain
play.
(1)
Press the [SETUP] key while the D2424LVmkII is
in the stop mode to switch to the SETUP display.
(2)
Display the “Chain Play MD?” menu via the Jog
dial and then press the [EXECUTE/YES] key.
The recorder will change to the display for setting
up of the chain play mode and the present setup
mode will flash (In the initial setup, “
Off
” will flash).
(3)
Select the desired mode via the Jog dial.
When the Jog dial is rotated, modes other than the
currently shown “
Off
” listed below can be selected.
“Off”
“Pause” (Pause mode)
“Auto P” (Auto play mode)
“Rpt” (Pepeat mode)
Refer to previous page
61 on the function of
each mode.
If the D2424LVmkII is played back after this, func-
tions of the mode selected will be executed from
the first program in the chain list.
Normally, in chain play as explained above, execu-
tion starts from the first program on the chain list
but any program of your choice can be specified
and chain play executed from that program.
For details, refer to “
Specify the program and execute
chain play
”.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Flashing
(4)
Press the [EXECUTE/YES] key after selecting the
mode.
The recorder will exit from the SETUP mode after
setup is completed.
In this step, if it was completed in the setup other
than the “
Off
” mode, the D2424LVmkII will
automatically locate to the “
AUTO RTN START point
”
of the first program in the previously setup “
Chain
list
” and stop.
If it was completed after setup to “
Off
,” the
D2424LVmkII will return to the first display of the
program prior to entering the SETUP mode.).
<The “Current” display after setup>
If the “
Chain Play?
” menu is set to other
than “
Off
” (“
Pause
,” “
Auto P
” or “
Rpt
”), then
exit from the SETUP mode, the current dis-
play will change as shown in example be-
low and, the display will be different from
when it is set to “
Off
.”
<When “Chain Play?” is set to “Off.”>
<When “Chain Play?” is set to other than “Off.”>
The above is an example showing that pro-
gram 03 (P03) activated by the ABS time
base, is set at fourth in the chain list.
As shown here, when the chain list is cor-
rectly setup and the “
Chain Play?
” menu
set to other than “Off,” in which order (For
example, “
c04
”) of the chain list had the
presently active program been setup, will
be indicated. Should it be changed to an-
other time base, the chain list number will
be indicated in the same manner.
F
S
M
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
ABS
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
F
S
M
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
ABS
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Upon setup of the previous “
Chain Play List
,” select the desired mode in the “
Chain Play MD?
” (Setup
of the chain play mode) menu in the same SETUP mode.
