123
Model D2424LVmkII Reference Manual (Changing the Initial Settings <SETUP mode>)
Setup of the stop function at the mark
At the “
Setup of the stop function at the mark point
”
menu, this sets whether or not D2424LVmkII should
automatically stop at the preset mark point (=lo-
cate point) during playback.
• Initial setting:
[Off]
• Options:
[OFF]
or
[On]
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of
the song data.
* The settings are maintained after you turn off the
power to the recorder.
(1)
While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
(2)
Turn the Jog dial to select “Mark Stop MD?” (“?”
flashes), then press the [EXECUTE/YES] key.
A flashing “
?
” will extinguish by pressing the
[
EXECUTE/YES
] key and the stop function at the
mark point information that was lit will being
flashing. Initial setting, it will show “
Off
”.
(3)
Select "On" or "Off" with the Jog dial and press
the [EXECUTE/YES] key again.
The selected stop function will be registered and
the Step-2 "?" will return to flashing.
(4)
Exit from the SETUP mode by pressing the [EXIT/
NO] key (or the [STOP] button).
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Flashing
To cancel the operation, or to restore the setting
obtained prior to the
[EXECUTE/YES]
key press,
press the
[STOP]
button or the
[EXIT/NO]
key. Each
time you press one of these keys, the recorder
returns to the previous hierarchy level of the
menu, and finally exits SETUP mode and displays
the previous Time Base.
Flashing
Setup of input/output Balance/Unbalance
Whether the D2424LVmkII rear panel analog input/
output connectors should be set to balanced or un-
balanced lines can be setup at the "
Setup of input/
output balance/unbalance
" menu. Initially, it is set for
unbalance but can be set to balanced input/output.
Because the setup content is registered in the
D2424LVmkII internal System ROM, it will be held
even though the current drive E-IDE hard disk is
replaced.
(1)
While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
(2)
Turn the Jog dial to select “BAL/UNBAL ?” (“?”
flashes), then press the [EXECUTE/YES] key.
The display will change as shown below and the
presently setup item will be displayed.
The blinking "
?
" will disappear when the [
EXECUTE/
YES
] key is pressed and the lighted item will change
to flashing.
"
UNBAL
" will flash in the initial setting.
• Initial setting:
[UNBAL]
(Unbalanced/-10dBV)
• Option:
[UNBAL]
(Unbalanced/-10dBV) or
[BAL]
(Ba4dBu)
* The settings cannot be saved and loaded as part of
the song data.
* The settings are maintained after you turn off the
power to the recorder.
(3)
Select the “BAL” or “UNBAL” with the Jog dial,
then press the [EXECUTE/YES] key again.
The selected item will be registered and "
?
" in Step-
2 will return to flashing.
(4)
Exit from the SETUP mode by pressing the [EXIT/
NO] key (or [STOP] button).
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
To cancel the operation, or to restore the setting
obtained prior to the
[EXECUTE/YES]
key press,
press the
[STOP]
button or the
[EXIT/NO]
key.
Each time you press one of these keys, the
recorder returns to the previous hierarchy level
of the menu, and finally exits SETUP mode and
displays the previous Time Base.
