136
Model D2424LVmkII Reference Manual (MIDI Implementation Chart/MMC List)
data length in the clipboard is less than 10ms, specifying
the <repeat count> will be limited to "01."
Also, by specifying the <mmc track>, paste operation can
be executed on other tracks in mono (one track unit) or
stereo units (tracks 1-2, 3-4, 5-6, 7-8....).
Since time corresponding to length of the move clipped
sound data is required to complete the move paste
operation, D2424LVmkII will immediately reply with "32
4E (<edit message=02 (active)>)" after receiving the
command.
Following completion of the move paste operation, "32 4E
(<edit message = 01 (completed)>)" will be sent.
If paste cannot be executed due to improper figures of the
previously registered auto punch in point, insufficient disc
capacity, no sound data is in the clipboard, etc., the
corresponding <edit message> will be replied.
12 4F (<channel><channel>): track exchange command
When the D2424LVmkII receives this command, the track
can be exchange between the specified <channel> <chan-
nel>. Especially, if the first <channel=00><channel=01>,
then exchange by grouping will be executed between chan-
nel 1-8 and channel 17-24, and if the next byte <chan-
nel=00> <channel=02>, then the exchange will be between
channel 9-16 and channel 17-24. If it cannot be executed
for some reason, an error message will be sent back.
13 3E: product new program command
When the D2424LVmkII receives this command, a new
program is compiled and the current program is
transferred to the new program. As compilation of the
new program is comparatively short time, it is replied with
"33 3E (<edit message=01 (completed)>)" immediately
upon completion of execution.
If it cannot be executed for some reason, an error message
will be sent back.
13 3F: delete current program command
When the D2424LVmkII receives this command, the
current program is deleted and succeeding programs
moved up and renumberd. If the deleted program is the
only tune existing in the track, a new program will be made
automatically.
As this delete current program is executed in a
comparatively short time, "33 3F (<edit message=01 (com-
pleted)>)" will be sent back immediately upon completing
the execution.
If it cannot be executed for some reason, an error message
will be sent back.
13 41 (<channel><channel>): digital in ch.select command
The audio signal input from SPDIF digital in to assigned to
the destination track specified by <channel>.
The first <channel> shown in the command is the SPDIF L
channel input, and the second <channel> the R channel
input. "<channel=0> <channel =0>" indicates the normal
analog input. In the D2424LVmkII, channels 1 and 2 only
can be selected for other than <channel=0>.
13 41 (<channel=7F><count><mmc track>): Adat in select
command
Channel = 7F indicates that it is Adat In. Normally, it will
be "<count=0>" and all channels will be inputs from Adat
In.
If <count=0><mmc track> is indicates, then only the tracks
selected will be Adat In inputs. "<channel=0><channel=0>"
indicates the normal analog input.
13 42 (<channel><channel>): digital out ch.select command
The source channel for digital out is selected.
Normally, the first <channel> shown will be the SPDIF L
channel data, and the second <channel> the SPDIF R chan-
nel output. (<00> <00>) is the default setting. By FDMS-3
V3.0, any channel within "1 ~ 8" (or 9 ~ 16 or 17 ~ 24) can
be selected.
13 42 (<channel=7F><channel=0>): Adat out select command
In a device which can be switched between SPDIF and Adat,
if the first display is <channel=7F>, then Adat Out can be
setup.
13 43(<program>): program change command
The command for PROGRAM CHANGE of the D2424LVmkII.
The present program number can be changed to the figure
indicated by <program>.
13 44 (<on/off>): click on/off command
The command for setting the metronome on/off of the
D2424LVmkII. When ON is set, the metronome signal will
be fed to the track 24 output of the D2424LVmkII.
13 46 (<on/off>): Bar/Beat Resolution ON/OFF command
The command for ON/OFF of the bar/beat resolution func-
tion of this equipments' current program.
13 47 (<midi sync>): Midi Sync Out command
The setup command for MIDI Sync Out mode of this equip-
ments' current program.
13 48 (<MTC offset mode>): MTC offset mode command
The setup command for MTC offset mode of this
equipment’s current program.
13 49 (<count=3> <on/off> <vari data>): Vari pitch command
13 49 (<count=1> <on/off>): Vari pitch command
The command for setting this equipments' vari pitch ON/
OFF and pitch data.
Control of ON/OFF only is possible at <count=1> and both
ON/OFF and pitch data can be set at <count=3>.
14 01 (<signature map>): Signature set command
The command for setting the meter of this equipment.
If a new data is registered at the bar position where a data
exists, the former data will be written over.
When this command is received, this equipment will reply
with "34 01 (<edit message>)."
Upon completing the registeration, <edit message> will reply
with "01 (completed)," or with "10 (over value error)" if
registeration is attempted at a non-existing point or an
erroneous figure is used.
14 02 (<tempo set map>): Tempo set command
The command for tempo set of this equipment.
If a new data is registered in a bar/meter where data
already exists, the former data will be written over.
When this command is received, this equipment will reply
with "34 02 (<edit message>)."
Upon completing the registeration, <edit message> will reply
with "01 (completed)," or with "10 (over value error)" if
registeration is attempted at a non-existing point or an
erroneous figure is used.
14 03 : Tempo map all erase command
When this command is received, this equipment will erase
all meter and tempo data in the current program and thus
return it to the default state (meter=4/4, tempo: =120).
Also, when this command is received, this equipment will
reply with "34 03 (<edit message>)."
