Forum 755000 Скачать руководство пользователя страница 49

Страница: 49 / 154

Operation Maintenance Manual

06-2018

PN 757000-D - Revision: 17 (up to SN 138212) Power Slip PS-500

RT/

STA

3.2

Transport

DANGER

Suspended load!

The falling load can cause severe, even
lethal injuries.

» Never stand beneath or in the

swing area of lifted loads

WEAR PROTECTIVE HELMET!

WEAR PROTECTIVE GLOVES!

WEAR SAFETY SHOES!

INFO

Safe Lifting Points!

- Lifting point locations are marked on the

PS-500.

• Make Sure all load hooks are fully installed in

the lifting point.

• It is advised to use pallets for longer

component transports.

» Thus, the safe transport of

FORUM Handling Tools

equipment is

ensured.

Principles for transport

1. Ensure that transport routes are sufficiently

dimensioned and marked.

» Ensure that persons are aware that transport is taking

place.

2. Always use pallets for longer transport distances.
3. The total weight (object to be trans means

of transport, e.g. forklift) must not exceed the
supporting capacity of the subsurface.

4. Ensure that only sufficiently qualified personnel

perform such work.

5. Always shut off PS-500 before transport and secure

against starting back up unintentionally.

» Start de-installation only after residual energy has

been dissipated.

6. Ensure that visual and audio contact exists between

the crane operator and operating personnel.

7. Secure the area against unauthorized entry.

» If necessary, mark the area with information signs to

warn of maintenance and repair work.

8. Secure moving parts in suitable manner.
9. Use only approved slinging and transport

equipment, which is in perfect condition and
suitable for the intended purpose.

» Observe specified load limits.

10. Secure PS-500 against Slipping/sliding.

» Observe PS-500 weight.

» Observe center of gravity.

11. Never stand under suspended loads.
12. Transport the PS-500 carefully.

» Do not fasten, lift or pull the PS-500 on not suitable

parts.

» Avoid sudden stops.

13. Always use hoisting equipment (slings, hoisting

cables, shackles, etc.), which has been inspected and
is sufficiently dimensioned.

14. Ensure that all installation and hoisting procedures

are accomplished in compliance with recognized
rules of practice and industrial standards.

• For detailed weight specifications refer to section 1.3

“Technical Data” on page 25, and refer to section
1.10 “Component Sizes” on page 33 also.

• FORUM Handling Tools recommends the use of the

Hook Up Kit (P/N 757000-HUK).

Содержание 755000



























































































































































Результаты поиска

Содержание 755000

Отзывы:

Похожие инструкции для 755000

Бренды по названию

Популярные бренды

Forum 755000, Руководство по эксплуатации

Результаты поиска

Содержание 755000

Отзывы:

Похожие инструкции для 755000

Бренды по названию

Популярные бренды